Ac Wiring Connections (Optional); Flow Switch Wiring Connections - Franklin Electric SubDrive Solar Manual De Instrucciones

AC Wiring Connections (Optional)

The SubDrive Solar controller has AC wiring connections for use with a generator when Solar DC
power is not available.
1. Make sure the generator is powered off.
2. Make sure the external DC disconnect switch is off.
3. Connect the cables from the generator to the Terminal Block labeled "Back-up AC" and marked
L1, L2, and GND (Figure 6) (Torque specification: 15 in-lbs/ 1.7 N-m).
L1 L2
BACKUP
AC

Flow Switch Wiring Connections

The SubDrive Solar controller makes use of a flow switch to protect the controller and motor when
there is not enough power to generate proper flow. The flow switch and sensor cable is included with
the SubDrive Solar QuickPAK and is required on all installations.
1. Connect the cables from the Flow Switch terminals NO and COM, and to the SubDrive Solar
terminal block labeled "TRIP" (Figure 7).
TRIP
CAUTION
Failure to properly install the included flow switch will result in reduced system performance and may
result in system damage.
COMM.
COMM.
STATUS
MENU SELECT
UP
DOWN
225979101,3
- +
RS-485
225996101,2 Error Codes
E1 E2 E3 E4 E5 E6 E7 E8 E9 Figure 6: AC Wiring Connection
Display
Status Run Idle Motor Under Locked External Open Short Overheated Internal
Mode Mode Underloaded Voltage Pump Trip Circuit Circuit Controller Reserved Error
WARNING – Operation of this equipment requires
detailed installation and operation instructions provided
Suitable for use on a photovoltaic circuit capable of delivering not more in the Installation/Operation manual intended for use
Service
than 50 DC amps short circuit current, or on a backup AC generator with this product. Additional copies of the
capable of delivering not more than 5000 amps symmetrical RMS current. Installation/Operation manual may be ordered by
See manual for allowed ratings of solar array (DC) and generator (AC).
contacting your local Franklin Electric representative.
Use 90 °C wire rated 600V min for DC and 300V min for AC. Diagnostic Aid
COM
Tighten terminals to 7 in-lbs. Tighten terminals to 15 in-lbs. NC Tighten terminals to 15 in-lbs.
NO
+ -
L1 L2 BLK RED YEL
(GND) (GND) (GRY) (BLK) (BRN) (GND)
RUN STOP TRIP
MOTOR
SOLAR PRIMARY BACKUP
DC AC
Multiple electrical power sources may be connected.
Disconnect all electrical power before servicing.
COMM.
COMM.
STATUS
MENU SELECT
UP
DOWN
Figure 7: Flow Switch Wiring Connection
225979101,3
- +
RS-485
225996101,2
Error Codes
E1 E2 E3 E4 E5 E6 E7 E8 E9
Display
Status Run Idle Motor Under Locked External Open Short Overheated Internal
Mode Mode Underloaded Voltage Pump Trip Circuit Circuit Controller Reserved Error
WARNING – Operation of this equipment requires
detailed installation and operation instructions provided
Suitable for use on a photovoltaic circuit capable of delivering not more
in the Installation/Operation manual intended for use
than 50 DC amps short circuit current, or on a backup AC generator Service
with this product. Additional copies of the
capable of delivering not more than 5000 amps symmetrical RMS current.
Installation/Operation manual may be ordered by
See manual for allowed ratings of solar array (DC) and generator (AC).
contacting your local Franklin Electric representative.
Use 90 °C wire rated 600V min for DC and 300V min for AC. Diagnostic Aid
COM
Tighten terminals to 7 in-lbs. Tighten terminals to 15 in-lbs. NC Tighten terminals to 15 in-lbs.
NO
+ -
L1 L2 BLK RED YEL
(GRY) (BLK) (BRN) (GND)
(GND) (GND) RUN STOP TRIP
MOTOR
SOLAR PRIMARY BACKUP
DC AC
Multiple electrical power sources may be connected.
Disconnect all electrical power before servicing.
17