Tabla de contenido
Publicidad
The pellet feed-box is empty.
NO PELLETS
No pellet feed.
The motor reducer does not feed pellets.
The door is not closed correctly.
The ash drawer is not closed correctly.
ALL DEPR
The combustion chamber is dirty.
The ue exhaust pipe is blocked/dirty
H2O OVERTEMPERA
Air in the system
TURE
Inadequate circulation
MIN H20 PRESSURE
The system pressure read by the pressure switch
ALARM
is too low.
H2O PROBE
H2O probe failure
MAX H20 PRESSURE
The pressure of the water has exceeded the max
ALARM
threshold
* PRESSURE SENSOR
Pressure di erential sensor faulty, disconnected
DAMAGED
or failure.
* AUGER CONTROL
Abnormal pellet loading.
* AUGER BLOCK
Abnormal operation of pellet motor.
* BOILER PROBE
Boiler probe failure.
* BUFFER TANK PROBE
Bu er tank probe fault.
The pellet feed-box is empty.
The door is not closed correctly.
* TANK EMPTY
The ash drawer is not closed correctly.
The combustion chamber is dirty.
The ue exhaust pipe is blocked
PWM INTERFACE
IPWM output interface damaged, in short
ALARM
circuit or not connected
The pump is operating but not with good
HOT PWM ALARM
performance. Undervoltage 160-194v.
Pump in circuit breaker protection mode.
The pump has stopped but is still operational.
STOPPED PWM ALARM
Undervoltage < 160v. Overvoltage.
Unexpected external ow.
The pump has stopped but is still operational.
STOPPED 2 PWM
Problem in a component di erent to the pump.
ALARM
Debris in installation.
Positioning in high temperature.
The pump has stopped permanently.
BLOCKED PWM ALARM
Pump blocked. Electronic module damaged
Pump blocked.
FLOW PWM ALARM
Liquid with high density.
Pipe obstructed.
AIR FLOW METER
Component disconnected or faulty
FAULT
The bottom of the burning pot or the
combustion chamber are dirty.
CLEAN CHECK UP 1 2
The door is not closed correctly.
*
The ash drawer is not closed correctly.
1
= START UP PHASE
The depression sensor is faulty.
2= WORK PHASE
The flue exhaust pipe is blocked
incorrect installation
* on models with this function.
TO FIND OUT WHERE YOUR NEAREST SERVICE CENTRE IS, CONTACT YOUR DEALER OR GO TO THE WEBSITE WWW.LANORDICA-EXTRAFLAME.COM
Check for the presence of pellets in the feed-box.
Adjust the pellet ow (see "Easy Set Up").
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Check cleanliness of the fumes pipe and the combustion chamber.
Possible air in the system; bleed the system. Lack of adequate circulation.
Lack of or inadequate safety zone.
The water in the stove has exceeded 95°C. Possible pump anomaly.
If the problem persists, restore operations must be performed by an
authorised technician.
Possible air in the system; bleed the system. Possible lack of water or leaks
due to anomalies in some system component.
If the problem persists, contact the after-sales centre
Contact after-sales centre
Possible air in the system; bleed the system. Check that the expansion
vessels are not damaged or under-dimensioned Check that the cold system
is loaded at the correct pressure
If the problem persists, contact the after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Check for the presence of pellets in the feed-box.
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Check cleanliness of the fumes pipe, of the sensor in the primary air
channel and the combustion chamber.
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Contact after-sales centre
Check that the holes at the bottom of the burning pot are completely free.
Check the cleanliness of the fumes pipe and the combustion chamber.
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Other restoration operations must be performed by an authorised
technician.
ENGLISH
75
Publicidad
Tabla de contenido
