Loading The Tool - Stanley Bostitch GFN1564K Manual De Instrucciones

2. Insert the fuel cell into the tool
© Stanley Bostitch
i. Push up and pull out the actuater (Fig. 6).
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
ii. Insert the fuel cell into the tool (Fig. 7), making sure
compliance for the products.
that the stem of the fuel cell lines up correctly with the
hole in the adaptor (Fig. 8).
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
iii. Close the actuater (Fig. 9).

5. LOADING THE TOOL

DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
CAUTION: When loading nails into tool:
● Do not depress trigger
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten. ● Do not depress contact arm
● Keep your face, hands, feet and other body parts,
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
as well as those of other persons away from the
produkterne.
nose to avoid possible injury during loading.
MODELS: GFN1664K / GFN1564K
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
1. Insert a nail strip into the rear of the magazine (Fig. 10).
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος 2. Slide the nail strip forward in the magazine (Fig. 11).
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
3. Pull the nail feeder past the nail strip towards the rear
of the magazine (Fig 12) to engage it on to the nail strip.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
Note: Nail strips of more than 10 nails must be used.
conformità CE per i relativi prodotti.
4. The nailer is now ready to operate.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
Removing the nails:
merking for produktet.
1. Pull the nail feeder to the back of the magzine slightly
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
and depress the button located in the feeder. (Fig. 13).
conformidade com a CE para os produtos.
2. Gently slide the nail feeder forwards, over the nail
strip.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
3. Slide the nails to the back of the magazine and remove.
(Fig. 14).
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
MODEL: GBT1850K
conformidad con las normas CE de los productos.
1. Press the latch on the back of the magazine and pull
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
back the cover. (Fig. 15)
stanowią deklaracji zgodności CE prezentowanych produktów.
2. Set the nail strip into the magazine, keeping the points
of nails in contact with groove at the base of the
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
channel. (Fig. 16)
stanowią deklaracji zgodności CE prezentowanych produktów.
3. Slide the nail strip to the front of the magazine into the
blade guide. (Fig. 17)
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
4. Push the cover forwards to close the magazine.
● Always keep the points of nails in contact with
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
Groove.
a termék CE-megfelelőségét.
● Use nail strip of more than 5 nails.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
4. The Nailer is now ready to operate.
conformitatea CE pentru produse.
Removing the nails:
1. Lightly press the stop lever and gently pull out the
magazine cover.
2. Remove the nails from the nailer.
CAUTION: To prevent unintentional operation, never
touch the trigger or place the top end of the contact arm
on a work bench on floor. Also, never face the nail outlet
toward any part of a person.
6. USING THE NAILER
CAUTION
● Squeeze the contact arm when drivng a nail,
otherwise the piston can not return correctly.
● Using the tool for an extended period may lead to oil
around the exhaust outlet or nose, resulting in
spattering.
● To ensure that the material to be nailed stays clean,
wipe off any oil that gets on the tool.
CYCLE RATES
These tools are designed to operate up to the following
cycle rates:
Intermittent Operation – 2 to 3 nails per second
Continuous Operation – 1000 nails per hour
Exceeding these rates could cause the tool to overheat,
resulting in loss of performance or damage to tool
components. By using the nailer at its recommended
cycle rate, you will be able to drive several thousand
nails in a typical working day.
SAFETY TRIP
These tools are supplied fitted with a sequential safety
trip and are marked with an inverted equilateral triangle
(▼). Do not attempt to use a tool marked in this way if
the safety trip is missing or appears damaged.
The sequential trip requires the operator to hold the tool
against the work with the safety trip depressed before
pulling the trigger. In order to drive additional fasteners,
the trigger must be released and the tool lifted away
from the work, before repeating.
This makes accurate fastener placement easier, for
instance on framing, toe nailing and crating applications.
The sequential trip allows exact fastener location
without the possibility of driving a second fastener on
recoil. The sequential trip tool has a positive safety
advantage because it will not accidentally drive a
fastener if the tool is contacted against the work or
anything else, while the operator is holding the trigger.