Tabla de contenido
Publicidad
conexiones de cableado ca (opcional)
El controlador SubDrive Solar cuenta con conexiones de cableado CA para su uso con un generador
cuando no hay alimentación CC solar disponible.
1. Asegúrese de que el generador esté apagado.
2. Asegúrese de que el interruptor de desconexión CC externa esté apagado.
3. Conecte los cables del generador al bloque de terminales identifi cado como "Backup AC"
(CA de respaldo) a los terminales L1, L2 y GND (Tierra). (Figura 6) (Especifi cación de torsión:
15 lb-in/1,7 Nm).
L1
conexiones del cableado del interruptor de fl ujo
El controlador SubDrive Solar utiliza un interruptor de fl ujo para proteger el controlador y el motor
cuando no hay alimentación sufi ciente para generar el fl ujo adecuado. El cable del sensor y del
interruptor de fl ujo se incluye con el SubDrive Solar QuickPAK y se requerirá en todas las instalaciones.
1. Conecte los cables de los terminales S1 y S2 del interruptor de fl ujo al bloque de terminales
identifi cado como "TRIP" (Disparo) (Figura 7).
Precaución
Si el interruptor de fl ujo incluido no se instala correctamente, se reducirá el rendimiento del sistema y
es posible que se produzcan daños en el sistema.
16
COMM.
COMM.
STATUS
MENU
SELECT
UP
DOWN
225979101,3
-
+
RS-485
225996101,2
E1
Display
Status
Run
Idle
Motor
Mode
Mode
Underloaded
Suitable for use on a photovoltaic circuit capable of delivering not more
than 50 DC amps short circuit current, or on a backup AC generator
Service
capable of delivering not more than 5000 amps symmetrical RMS current.
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Diagnostic Aid
COM
Tighten terminals to 7 in-lbs.
Tighten terminals to 7 in-lbs.
Tighten terminals to 15 in-lbs.
Tighten terminals to 15 in-lbs.
Tighten terminals to 15 in-lbs.
NC
NO
L2
+
+
-
L1
L1
L2
L2
(GND)
(GND)
(GND)
(GND)
(GND)
RUN
SOLAR PRIMARY
SOLAR PRIMARY
SOLAR PRIMARY
BACKUP
BACKUP
BACKUP
BACKUP
DC
DC
DC
AC
BACKUP
Multiple electrical power sources may be connected.
Disconnect all electrical power before servicing.
AC
COMM.
COMM.
STATUS
MENU
SELECT
UP
DOWN
225979101,3
-
+
RS-485
225996101,2
E1
Display
Status
Run
Idle
Motor
Mode
Mode
Underloaded
Suitable for use on a photovoltaic circuit capable of delivering not more
Suitable for use on a photovoltaic circuit capable of delivering not more
Suitable for use on a photovoltaic circuit capable of delivering not more
Service
than 50 DC amps short circuit current, or on a backup AC generator
than 50 DC amps short circuit current, or on a backup AC generator
than 50 DC amps short circuit current, or on a backup AC generator
capable of delivering not more than 5000 amps symmetrical RMS current.
capable of delivering not more than 5000 amps symmetrical RMS current.
capable of delivering not more than 5000 amps symmetrical RMS current.
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Diagnostic Aid
COM
Tighten terminals to 7 in-lbs.
Tighten terminals to 7 in-lbs.
Tighten terminals to 15 in-lbs.
Tighten terminals to 15 in-lbs.
NC
NC
NC
NO
NO
+
+
-
L1
L1
L2
L2
(GND)
(GND)
(GND)
(GND)
RUN
SOLAR PRIMARY
SOLAR PRIMARY
BACKUP
BACKUP
DC
DC
AC
AC
AC
Multiple electrical power sources may be connected.
Multiple electrical power sources may be connected.
Multiple electrical power sources may be connected.
Disconnect all electrical power before servicing.
Disconnect all electrical power before servicing.
Disconnect all electrical power before servicing.
Disconnect all electrical power before servicing.
TRIP
Error Codes
E2
E3
E4
E5
E6
E7
E8
E9
Figura 6. Conexión del cableado CA
Under
Locked
External
Open
Short
Overheated
Internal
Voltage
Pump
Trip
Circuit
Circuit
Controller
Reserved
Error
WARNING – Operation of this equipment requires
detailed installation and operation instructions provided
in the Installation/Operation manual intended for use
with this product. Additional copies of the
Installation/Operation manual may be ordered by
contacting your local Franklin Electric representative.
Tighten terminals to 15 in-lbs.
BLK
RED
YEL
STOP
TRIP
(GRY)
(BLK)
(BRN) (GND)
MOTOR
Figura 7. Conexión del cableado del interruptor
de fl ujo
Error Codes
E2
E3
E4
E5
E6
E7
E8
E9
Under
Locked
External
Open
Short
Overheated
Internal
Voltage
Pump
Trip
Circuit
Circuit
Controller
Reserved
Error
WARNING – Operation of this equipment requires
detailed installation and operation instructions provided
in the Installation/Operation manual intended for use
with this product. Additional copies of the
Installation/Operation manual may be ordered by
contacting your local Franklin Electric representative.
Tighten terminals to 15 in-lbs.
BLK
RED
YEL
(GRY)
(BLK)
(BRN) (GND)
STOP
TRIP
MOTOR
Publicidad
Tabla de contenido
