Tru-Test XRP EID READER Manual Del Usuario página 12

Appendix A – Specifications and Regulatory compliance statements
Item
Standards compliance
Ingress protection
Dimensions
Weight
Supply voltage
Tag compatibility
Operating frequency
Read range (typical)*
Read rate*
Indicators
Sound
Communications interface
User interface
Antenna tuning
Operating temperature
Storage temperature
Synchronisation port (Synch model only)
* Actual read range (read distance) and read rate depends on the tag manufacturer, the size of the tag, orientation of the tag to the antenna and the influence of electronic
noise.
FCC notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC warning
Note: Users are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
The XRP-1 (Standard) or XRP-1S (Synchronisable) EID Reader supplied has been approved for use only with approved external antennas described in this manual; use of any other antenna may
void the user's authority to operate the equipment. This device and its antenna(s) must not be cohabited or operate in conjunction with any other antenna(s) or transmitter(s).
Industry Canada notice
This radio transmitter, model XRP-1 (Standard) or XRP-1S (Synchronisable), has been approved by Industry Canada to operate with the antenna types listed below, with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.

Sheep EID Antenna, for use with Tru-Test XRP-1 (Standard) or XRP-1S (Synchronisable) EID Reader – Gain (0 dBi), Impedance (2 kΩ)

Cattle EID Antenna, for use with Tru-Test XRP-1 (Standard) or XRP-1S (Synchronisable) EID Reader – Gain (0 dBi), Impedance (2 kΩ)
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Industry Canada warning
Installation within Canada:
To maintain compliance with Industry Canada RF exposure compliance requirements, please follow the operation instructions as documented in this manual. This equipment should be installed
and operated with a minimum distance of 20 cm between the antenna and your body.
Tru-Test Limited hereby declares that this EID Reader is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of
conformity may be consulted at http://www.tru-test.com/weighing/pdfs/EC_DoC_XRP-1.pdf
12
Conditions
RFID:
ISO 11784, ISO 11785
IP 66
220 mm x 171 mm x 55 mm
1040 g
11.6 V dc to 27 V dc, 7 W, reverse polarity protected.
Reads both ISO HDX and ISO FDX-B.
134.2 kHz ±5 ppm
HDX - 1 m FDX - 1 m (with Tru-Test Cattle Antenna).
HDX - ~850 FDX - ~1000 (max. reads per minute).
Red 'Power On' LED, Green 'Tag Read' LED.
Buzzer sounds on new tag read and faults.
RS232, 9600, N, 8, 1, no flow control.
CONFiG XRP software.
Enhanced fast auto tuning.
-20° C to +55° C
-40° C to +85° C
True carrier synchronisation option when multiple XRP Readers are being used.
EMC and Radiocommunications:
AS/NZS 4268 (New Zealand)
AS/NZS CISPR 22 (in accordance with MS 27) (Australia)
RSS-210 (Canada)
ETSI EN 300-330-2, ETSI EN 301-489-3 (Europe)
FCC (47 CFR 15 Subpart C) (USA)