Publicidad
Idiomas disponibles
Idiomas disponibles
Clock regulation
Press and hold the key "M" for 2 seconds to access the "CLOCK" menu. This allows you to set the internal electronic board clock.
By then pressing the key "M", the following data appears in sequence and can be regulated:
day, month, year, hour, minutes, day of the week.
The wording "SAVE??" will appear for confirmation with "M". This will allow you to check that the operations performed are correct, prior
to completion (the wording "SAVE" will then be shown on the display).
Weekly timer
Press and hold the "M" key on the remote control for 2 seconds. This turns on the clock regulation and by pressing the '+' key, the wee-
kly timer function is accessed, with the display showing the description "PROGRAMM ON/OFF". This function allows you to set a
number of times the insert turns on and off per day (up to a maximum of three), each day of the week.
As you confirm the display with the key "M", one of the following options will appear:
NO PROG. (no programme set)
DAILY PROGRAM (single programme for every day of the week)
WEEKLY PROGRAM. (specific programme for each day individually)
Use the "+" and "–" keys to switch between programmes.
Use key "M" to confirm the option "DAILY PROGRAM" to choose the number of programmes (turn on/off) to be carried out per day.
Use the "DAILY PROGRAM" to set identical programme/s for every day of the week.
By then pressing the "+" key, the following can be seen:
- Prog. no.
- 1st prog. (one turn on and one turn off per day), 2nd prog. (identical), 3rd prog. (identical)
Use the "–" key to show in reverse order.
If the 1st programme is selected, the turn on time is shown.
The display shows: 1 "ON" at 10 Use the "+" and "–" key to change the hour. Confirm with the "M" key.
The display shows: 1 "ON" at 30 Use the "+" and "–" key to change the minutes. Confirm with the "M" key.
The same applies for the turn-off time to be set and for subsequent turning on and off.
Confirm by pressing "M" and the wording "SAVE??" will appear on the display.y.
When confirming "WEEKLY PROGRAM", you will need to choose the day to which the programming is to apply:
1 Mon ; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sa; 7 Sat
Once you have chosen the day, use the "+" and "–" key and confirm with the "M" key, to programme in the same way as for the
"DAILY PROGRAM", choosing whether or not to enable a programme for each day of the week, and if so choosing number of inter-
ventions and at what times.Should you make an error during programming, you can leave the programme without saving. As you press
a key,
the display will show the word "NO SAVE".
Variation feeding pellets (ONLY AFTER SUGGESTED BY DEALER)
Press and hold the "M" key on the remote control for two seconds. Scroll through the display instructions using the "+"
and "–" keys, to the description "ADJ-PELLET". By confirming this function using the menu key you can adjust the supply of pel-
lets, by reducing the set value, you decrease the supply of pellets, increasing the set value increases the supply of pellets. This fun-
ction can be useful in the event that one changes the type of pellets used, no longer using those for which the stove was calibrated,
thus necessitating an adjustment of the load setting.
Should this correction not suffice, contact the Edilkamin-authorised Dealer, to establish the new operating axis.
Notes on flame variability: Any changes in the state of the flame depend on the type of pellets used, as well as on normal variation
of solid fuel flames and on the periodic cleaning of the crucible the stove automatically carries out (Note: This does NOT replace
the necessity cold vacuuming by the user prior to start up).
LOW BATTERY INDICATOR
When the battery icon lights up it indicates that the batteries inside the radio control are almost flat. Replace them with three new
batteries of the same model (size AAA 1.5V).
- Do not use new batteries with used ones.
- Do not mix brands and different types as every type and brand has a different capacity.
- Do not mix traditional batteries with rechargeable ones;
- Do not try recharging alkaline and zinc-carbon batteries as this can cause them to break and/or a liquid leakage.
In accordance with Art. 13 of the Legislative Decree No. 151, dated 25 July 2005, "Implementation of Directives: 2002/95/EC, 2002/96/EC and
2003/108/EC, pertaining to the reduction of hazardous substances used in electrical and electronic equipment, as well as disposal of waste".
The crossed-out wheeled bin symbol shown on the equipment or on the packaging indicates that the product must be disposed of separately at the
end of its useful life. Therefore, at the end of the equipment's useful life, the user must hand in the equipment to suitable collection facilities for
electrical and electronic waste, or return it to the retailer when a new, equivalent appliance is purchased in a ratio of one to one.
INSTRUCTIONS FOR USE
INFORMATION FOR USERS
46
Publicidad
