Blackstar Amplification ID:CORE STEREO 100 Manual De Uso página 9

Reamping
The amplifier can be switched into Reamping Mode via the Blackstar INSIDER
software. This is a non-storable setting and will be switched off either when the
USB cable is removed, or when the amplifier power is switched off.
When activated, Reamping Mode allows the amplifier to accept a pre-recorded, dry
guitar signal via USB and return a fully processed audio signal. This return signal can
then be captured using recording software on the connected PC or Mac.
Footcontrollers
FS-13 2-way footcontroller (supplied)
Connect this footcontroller to the Footswitch socket on the rear of your amplifier
using any standard mono guitar cable or speaker cable (supplied).
Action
A (press)
B (press)
B (hold)
A + B (press)
A + B (hold)
By default, your FS-13 footcontroller will be in Looper Mode (see table above) Switch
'A' is used to start and finish recording your loops and overdubs, and switch 'B' will
stop the loop playback, or cancel the current overdub if still recording. A single press
of both switches 'A' and 'B' simultaneously will undo the last recorded overdub.
Holding switch 'B' will erase the loop memory.
By holding down both the 'A' and 'B' switches for 3 seconds you can set your
footcontroller to Patch Mode. In this mode, button 'A' will toggle between the
patches in Channel 1 and Channel 2 of the currently active Bank. Pressing button
'B' will scroll 'up' through the first 3 Banks of patches, operating in the same way
as the BANK switch on the amplifier front panel. The operation of Patch Mode can
be changed via the Blackstar INSIDER software, as reflected in the table above.
Simply hold down both the 'A' and 'B' switches again for 3 seconds to change
back to Looper Mode.
The current mode of the FS-13 footcontroller will be stored when you power off
the amplifier, and will be and recalled each time you power on. Upon powering
on the amplifier with the FS-13 footcontroller connected (or connecting the FS-13
footcontroller with the amplifier already powered on) the current mode of the
footcontroller will be indicated by an animation using the MANUAL, BANK, CH1,
CH2 and CH3 LEDs. Looper Mode will be indicated by a 'looping' count up of these
LEDs, whereas Patch Mode will be indicated by these LEDs flashing simultaneously
twice before returning to normal operation.
16
LOOPER MODE PATCH MODE
Toggle Scroll
Play/Record/Start and Patch toggle (CH1 and CH2
Patch Down (1-12)
Stop overdub of the current BANK)
Stop playback/Cancel BANK scroll up Patch Up (1-12)
Erase loop memory - -
Undo last overdub - -
Switch to PATCH mode Switch to LOOPER Mode Switch to LOOPER Mode
FS-12 5-way programmable footcontroller (not supplied)
Connect this footcontroller to the Footswitch socket on the rear of your amplifier
using any standard mono guitar cable or speaker cable.
AMP
A B
Switches 'A'-'C' correspond to the 'CH 1' – 'CH 3' switches on the front panel
of your amplifier. Pressing any of the 'A'-'C' footcontroller switches will recall the
corresponding patch within the current Bank. Banks can be navigated by a single
press of both switches 'A' and 'B' simultaneously (Bank down) or a single press
of both switches 'B' and 'C' simultaneously (Bank up). All 36 amplifier patches (12
banks of 3) can be accessed using the FS-12 footcontroller.
Switches 'D' and 'E' on the FS-12 footcontroller are programmable and can be
configured to a number of different functions to suit your preference. By default,
Switches 'D' and 'E' will control the Looper feature of the amplifier, and will behave
as described in the following table.
To change this default setting, connect the amplifier
LOOPER MODE
to your computer via USB and use the free Blackstar
INSIDER software to make your personal selection from
Action
various options such as Modulation/Delay/Reverb On/Off,
Play/Record/Start and
D (press)
Stop overdub
Modulation/Delay Tap Tempo, Super Wide Stereo On/
E (press) Stop playback/Cancel
Off, amongst others. Please see the Footcontroller section
E (hold) Erase loop memory
of the INSIDER software for detail of the programmable
D + E (press) Undo last overdub
functions.
Holding down the 'D' and 'E' switches will activate Tuner Mode of your amplifier.
With the multifunctional FS-12 footcontroller you gain access to a fully chromatic
tuner with note and cents display information appearing on the footcontroller display
and LEDs. Press any switch to exit Tuner Mode.
FS-12 + FS-13 7-way switching
Connect the FS-12 5-way footcontroller to your amplifier as detailed above, then
connect your supplied FS-13 2-way footcontroller to the 'EXT.' socket of your FS-12
footcontroller, using any standard mono guitar cable or speaker cable.
AMP
A B C D
FS-12
In this configuration you can add two extra, programmable switches which are
configurable via the Blackstar INSIDER software. Please see the Footcontroller
section of the INSIDER software for detail of the programmable functions.
By default, switch 'A' on your FS-13 will toggle the current Modulation effect, and
switch 'B' will toggle the current Delay effect. When using this 7-way switching
configuration the two markers at right side of the display of the FS-12 will show the
on/off state of the effect for each switch, as shown below.
EXT.
C D E
EXT.
E
FS-13 (supplied)
A ON
FS-13 Effect switch
toggle states
B ON
17