Publicidad
Idiomas disponibles
Idiomas disponibles
www.groupdynamics-laundry.com
sales@groupdynamics.lv
The dryer has a 1/2' gas inlet).
All gas models are prepared and calibrated
to operate on propane gas (LPG), water
gauge pressure 300 mm.
Install a pressure regulator (see table be-
low), a cock and a gas filter ahead of the
appliance.
Make sure dirt does not enter the valve's
body during assembly.
Carry out a leak test as follows:
Ignite burner/s. By the use of a brush, apply
a soapy water solution on the gas inlet and
outlet joints. Check for bubbles. If any,
demount the relevant pipe, clean the thread
and assemble back again. Do not use corro-
sive soap.
The gas duct must not be smaller in diameter
than the machine inlet. Choose size also
according to the maximum requirement of
the dryer.
Type of gas
Running pressure
water
column mm
Liquid
270-350
propane
Natural
80-180
If several dryers are serial-connected to the
same gas supply, install one gas pressure sta-
biliser for each dryer.
5.7.1 CALIBRATION INSTRUCTIONS
FOR OPERATION ON NATURAL GAS
Change the nozzle that is on the right of the
burner. Make sure the diameter of the new
nozzle is consistent with the following table:
Ø Nozzle mm
Model
L.P.G.
G30
ERE 83
1,3
5.7.2 VALVE ADJUSTMENT
1) Switch the machine on; select a cycle.
2) Connect a pressure gauge to the outlet
pressure tap.
3) Remove cap from pressure adjusting
screw.
4) By the use of a screwdriver, turn the
adjusting screw slowly until the required
burner pressure is reached. Turn clockwise
to increase pressure; turn counterclockwise
to decrease pressure.
5) Put the screw's cap back.
Note: For liquid propane gas (LPG) pressure
adjustment is not required. Just turn the
adjusting screw down to the end (clock-
wise).
INSTRUCTIONS FOR
6. INFORMATION ON THE DRYER
6.1 MACHINE DESCRIPTION (FIG. 2, 3)
1) Lid covering the control circuit
2) Temperature selecting knob
3) Buzzer control
4) Drying cycle selector knob
5) Laundry loading door
6) Lower panel
7) Fumes exhaust outlet (Ø 100 mm)
8) Power supply
9) Gas inlet (gas models only)
10) Lint filter.
6.2 COMPLETE RANGE OF APPLICA-
TIONS
Your appliance was designed to dry fabrics
of different kinds, wool, cotton, linen.
Select drying temperature according to fab-
mbar
ric type.
Make sure the label on the garment admits
25-30
tumble drying.
6.3 INFORMATION ON THE ELEC-
8-18
TRIC SYSTEM
The built-in electrical system is composed
of safety and control devices on a plate
located on the upper rear part of the machine.
The relevant diagrams and part lists are
reported further on.
6.4. DOCUMENTS CERTIFYING
MACHINE CONFORMITY
The tumble dryer described in the present
manual complies with the standards on page
1 and the following standards:
73/23/CEE, 93/68/CEE
Natural gas
89/336/CEE, 92/31/CEE, 93/68/CEE
and regulations:
G20
EN 60335-1, EN 60335-2-44
2,2
EN 55014, EN 61000-3-2, EN 61000-3-3
EN55104.
7. INSTRUCTIONS FOR USE
7.1 OPERATION
Turn the dryer on by the main cutoff switch
on the wall. Open the gas cock (gas models
only).
Sort the garments to be dried according to
materials.
The residual moisture in the laundry to be
dried must not exceed 100%.
Make sure buttons, zips, clasps and buckles
are covered or facing inside.
Use low temperatures with clothes includ-
ing plastic seams, with stamped fabrics or
garments having plastic parts.
USER
14
7.2 USE
a) Clean the filter.
b) Load half of the dryer capacity with the
laundry
c) Close the door.
c) Select the desired temperature.
d) Select the desired time.
e) Push the timer knob to switch the
appliance on.
f) Unload the drier as soon as the cycle has
finished.
7.3 HANDY TIPS
Do not load the appliance with fabrics that
were cleaned, soaked, impregnated or
washed with inflammable or explosive sub-
stances. If necessary, wash them in water
beforehand.
To avoid personal injure and property dam-
age, read the instructions carefully before
Publicidad
