Technical Data; Assembling Procedure - DITEC CIVIK Manual Para Lensablaje, La Instalacion Y La Manutencion

1.

TECHNICAL DATA

Power supply
Absorption
Accessories power supply
Thrust
Opening speed
Closing speed
Intermittence
Max door weight
Temperature
Degree of protection
2. ASSEMBLING THE AUTOMATIC SYSTEM
Unless otherwise specified, all measurements are expressed
in millimetres (mm).
2.1 Components references
REF CODE
DOITCVK16
1 DOITCVK22 Operator
DOITCVK33
2 Power supply plug
3 Radar
4 Photoelectric cells
5 Push-button
6 Control and drive unit
7 Belt transmission unit
8 Belt attachment bracket
9 KCIVIK1 Carrier unit
10 Rabbed lock
11 Wire bracket
12 Housing heads
13 KXL037K
Belt 20 m
KXL037A
14 V3760N33
Housing
V3760N66
15 VSP25V25 Seal brush 2,5 m
16 V3759N33
V3759N66
Carter
V3759G33
V3759G66
17 RGR3511200 Gasket 40 m
18 Lock
CIVIKLA
19 Block hook-up bracket
20 OCL Radio receiver
21 CIVIKAL Wood door attachment
22 CIVIKAC Glass door attachment
23 0KP515AB Sliding guide (10 pz)
24 0KP369 Sliding guide for glass wing (10 pz)
25 K1356N30
K1356N60
Glass wing profile
K1356G30
K1356G60
26 CIVIKGCT Second door wing pulling unit
27 KCIVIKGCL Second door unit
6 Control and drive unit
7 Belt transmission unit
26 Belt attachment bracket - Pulling unit
KCIVIK1T
10 Rabbed lock
11 Wire bracket
12 Housing heads
CIVIK 1 WING
230 V~ / 50-60 Hz
0,2 A
24 V= / 0,3 A
30 N
0,4 m/s
0,2 m/s
S2=20 min / S3=30% S2=20 min / S3=30%
60 kg
-20° C / +55° C
IP20
DESCRIPTION
CIVIKJ 1 WING CIVIK 2 WINGS
120 V~ / 60 Hz 230 V~ / 50-60 Hz
0,4 A
24 V= / 0,3 A 24 V= / 0,3 A
30 N
0,4 m/s
0,2 m/s
S2=20 min / S3=30%
60 kg
-20° C / +55° C -20° C / +55° C
IP20

2.2 Assembling procedure

The supply modes for the CIVIK automations are as follows:
kit of components to be assembled;
automations assembled on a door wing in three different lengths.
To assemble the components kits, to reduce the standard LT
dimensions, or to carry out an automation for two door wings,
proceed as follows.
- Cut the box and the casing as indicated in fig.3.
NB: remove any cut residues from the aluminium, and clean the
carriage slide guides in particular.
- Assemble the necessary components as follows:
CIVIK 2 door wings, see page 3 or 8;
CIVIK 1 door wing with opening to the right, see page 4 or 9;
CIVIK 1 door wing with opening to the left, see page 5.
- Insert the belt in the motor, rotating the pin [A] as indicated
in the figure.
- Join the belt in line with the belt attachment bracket, as
indicated in the figure (on the right of the belt attachment
pulling unit [26]). Cut any excess.
8
13
- Tighten the belt correctly, moving the belt transmission [7]
to the left.
- Tighten all screws and secure the heads to the box.
19
CIVIKJ 2 WINGS
120 V~ / 60 Hz
0,2 A 0,4 A
24 V= / 0,3 A
30 N 30 N
0,8 m/s 0,8 m/s
0,4 m/s 0,4 m/s
S2=20 min / S3=30%
80 kg 80 kg
-20° C / +55° C
IP20 IP20
A
26
GB
13
CIVIK - IP1953