Install The Door Control - Craftsman 139.53976SRT Manual Del Propietário

iNSTALLATiON STEP 6
install the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet where small children cannot reach,
away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in new
home construction), it may be mounted to a single gang
box (Figure 2). NOTE: After installation, a green
indicator light behind the cover will indicate proper
connection. If not lit, the Lock and Light features will not
function (reverse wires to correct).
1. Strip 1/4" of insulation from one end of bell wire and
connect to the two terminal screws on back of door
control by color: white to W and white/red to R.
2. Remove the push bar cover by gently prying off the
top edge with a coin or screwdriver. Fasten with
6ABx1=1/4" self-tapping screws (standard installation)
or 6-32x1" machine screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" to protrude above
wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid
cracking plastic housing. Do not overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Be careful
not to pierce wire with a staple, creating a short or
open circuit.
4. Connect the bell wire to the terminal screws on the
motor unit panel: white to 2; white/red to 1.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach
entrapment warning label to wall near door control,
and manual release/safety reverse test label in a
prominent location on inside of garage door.
DO NOT connect power and operate opener at
this time. The trolley will travel to the full open
position but will not return to the close position
until the sensor beam is connected and properly
aligned.
HARDWARE SHOWN ACTUAL SIZE
_ IIlllMIMlllllllll II IIIll]>
6AB x 1-1/4" Screw
(standard installation)
6-32 x 1" Screw
(pre-wired installation)
Dry Wall Anchors
Insulated
Staples
Lock
Lighted
Push Bar
Light
Sutton
PASSIVEINFRARED
CONTROLCONSOLE
Toprevent possible SERIOUS INJURYor DEATH from
electrocution:
• Be sure power is not connectedBEFORE installing door
control.
• ConnectONLYto 24 VOLTlow voltage wires.
Toprevent possible SERIOUS INJURYor DEATH from a
closing garagedoor:
• Install door control within sight of garagedoor, out of
reachof childrenat a minimum heightof 5 feet, and away
from all moving parts of door.
• NEVER permit children to operateor play with door control
push buttons or remote control transmitters.
• Activatedoor ONLYwhen it can be seenclearly, is properly
adjusted,and thereare no obstructionsto door travel.
• ALWAYS keepgaragedoor in sight until completelyclosed.
NEVER permit anyoneto cross path of closing garagedoor.
i Outside Keylock Accessory Connections To opener terminal screws: white to 2; white/red to 1
Figure 1
STANDARD WALL MOUNT
To Replace
Insert Top
Tabs First .-
Indicator Switch
Light Push Bar Cover T °N
OFF
Figure 2
PRE-WIRED INSTALLATION
24 Volt
2-Conductor
Bell Wire in
Gang Box
To Replace,
Insert
TOsP qlab
t s
Detector ION
I Switch OFF
Light Push Bar Cover
Top
Mounting
Hole
BACK VIEW
Bell
Wire
Terminal
Screws
Bottom
Mounting
Hole
Opener
Terminal Screws
Antenna
18