Torch Button Mode - Platec INVERTER 250W Manual De Instrucciones

L W P
ED ELDING ARAMETER
MMA welding current.
L3
TIG welding current.
Second welding current in Bi-level
L4
TIG mode.
L5 Base current.
L6 Peak time.
L6-
Pulse frequency.
L7
L8 Slope-down time.
L9 Final current.
L10 Post-gas time.
- Spot welding time.
L11 Pre-gas time.
L12 Starting current.
L13 Slope up time.
- Arc-force.
- Hot-start.
- Maximum pedal current
- Minimum pedal current.
• SUBMENU KEY S2. In the MMA modality, by pressing
the S2 key, you can access the regulation of the Arc-
force and the Hot-start.
In all the welding modalities, by pressing the S2 key for 2
seconds, you can access the PROGRAMS SUBMENU.
LO appears on the display (LOAD PROGRAM, to load
the program). By using the encoder the other functions
can be displayed: SA (SAVE PROGRAM, to save the
program) and Er (ERASE PROGRAM, to erase the
program). To select the desired function, press the S2
key.
There are 50 locations available to memorize programs
(from P1 to P50), plus the program P0 to load the default
values (this program is not available when saving and
erasing).
To confirm the operation with the chosen program press
the S2 key, otherwise after 2 seconds you will
automatically be returned to the main menu. In the saving
and erasing functions, the locations that already contain
a program are displayed with the flashing number of the
program.
• S3: Selection key for TIG WELDING PROCESS.
The available procedures in the TIG modality are:
• Two-stroke lift-arc (2
• Four-stroke lift-arc (4
• Two-stroke H (2
F
• Four-stroke H
F
• Four-stroke H
If the led next to the symbol is on, it indicates the
selection of the parameter.
I N V E R T E R 2 5
I N V E R T E R 2 5
M M D
IN AX
10 250
5 250
10 200
10 90
1 99
0.1 500
0.0 25
5 250
0.0 25
0.1 9.9
0.0 10
2 200
0.0 25
0 99
0 99
5 250
1 90
)
T
)
T
H )
T F
(4 H )
T F
Bi-level (B )
F ILEVEL
0 W
0 W
U
EFAULT M
80 A
80 A
Only Bi-level TIG, percentage of the welding current. Adjustable from
50 %
Only pulsed TIG, percentage of the welding current. Adjustable from the
40 %
50 %
100 Hz
0.0 s
5 A
5 s
0.1 s
0.1 s
50 %
0.0 s
Only MMA, visualized on the display with Axx (xx = welding current
30 %
Only MMA, visualized on the display with Hxx (xx = welding current
50 %
This is only present if the remote control function is enabled and if a
80 A
This is only present if the remote control function is enabled and if a
5 %
We will now briefly describe the sequence used for
welding in each process:
Touch the piece being worked with the electrode of the
torch.
Press (1T) and keep the button for the torch held down.
Slowly lift the torch to strike the arc.
The WELDING CURRENT goes to the value set, carrying
out an ASCENT RAMP if necessary (adjustable time).
Release (2T) the button to start the process of
completing the weld.
The current goes to the FINAL CURRENT value set in a
period equal to the DESCENT RAMP time (adjustable).
The electric arc goes out.
The supply of gas continues for a period equal to the
POST-GAS time (adjustable).
Touch the piece being worked with the electrode of the
torch.
Press (1T) and release (2T) the button of the torch.
Release the torch slowly to strike the arc.
The WELDING CURRENT goes to the value set, carrying
out an ASCENT RAMP if necessary (adjustable time).
Press (3T) and keep the button held down to start the
process of completing the weld.
The current goes to the FINAL CURRENT value set in a
period equal to the chosen DESCENT RAMP time
(adjustable).
The electric arc stays lit, and is supplied by a current
equal to the FINAL CURRENT (adjustable).
Under these conditions, it is possible to carry out the
closing of the weld bath (CRATER FILLER CURRENT).
1 7
1 7
N
OTES
Adjustable from front and remote control.
Adjustable from front and remote control.
the front.
front.
Only pulsed TIG. Adjustable from the front.
Only pulsed TIG. Adjustable from the front.
Only TIG. Adjustable from the front.
Only TIG. Adjustable from the front.
Only TIG. Adjustable from the front.
Only TIG. Adjustable from the front.
Only TIG. Adjustable from the front.
Only TIG, percentage of the welding current.
Only TIG. Adjustable from the front.
percentage).
percentage).
pedal command is installed.
pedal command is installed.

TORCH BUTTON MODE

2 L -A W
T IFT RC ELDING
4 L -A W
T IFT RC ELDING
E n g l i s
E n g l i s
h
h