Handling And Storage; Handling; Storage; Installation - LAVAZZA BLUE LB2300 Instrucciones Para El Uso

Display Meaning
Lavazza The coffee grounds drawer has
Emptying
been removed following a warning
cof.groun.drawer
from the machine.
Wait please...
Lavazza The machine has interrupted the
Brewing
brewing cycle.
interrupted
Wait please...
Lavazza
The machine is in energy saving
Stand-By
mode.
Press a key
to start
Lavazza The machine is priming the water
Loading
circuit.
Water
Wait please...
Lavazza The descaling fi lter must be
replaced.
Ready
Filter replac.
Appears automatically when
Lavazza
Rinsing
programming the brew unit
C to terminate
washing every 24 hours.
Enter to confirm
Only for machines with Water
Lavazza
Network.
Water network
The water supply network has
interrupted
been cut off.
Only for machines with Water
Lavazza
Network.
Empty and fill
The machine is able to function
water tank
Press Enter using the tank positioned at the
rear.
Problems Causes
The machine does The machine is not connec-
not switch on. ted to the electric network
The main power button has
not been pressed
The machine does No message on the display
not work
If Out of Service message
11 appears on the display
If Out of Service message
2x (e.g. 21) appears on the
display
If Out of Service message
3x, 5x, 6x, 7x (e.g. 55) ap-
pears on the display
If Out of Service message
8x or 9x appears on the
display
Installation of the machine - Service Provider Manual
Action
Empty the coffee grounds drawer. Do not insert the
drawer while this message shows.
An alarm signal has been triggered, terminating
the brewing cycle. If necessary, contact the service
provider.
Press any button or open the capsule loading tray to
activate the machine.
Wait for this step to be successfully completed by the
machine.
Request assistance from the service provider.
Via the keypad start or disable the rinse cycle (see
section 4.5)
Request assistance from the service provider.
Request assistance from the service provider.
Fill the tank as described in section 4.1 and use the
machine. Press button (15).
Solutions
Contact the Service Provider.
Turn on the machine via the main power button.
Contact the Service Provider
Check if the previously inserted capsule is in the capsule
loading tray. If so, replace the capsule with another one,
then turn the machine off and back on again. If the problem
persists, contact the Service provider.
Check that the water tank is full and correctly inserted into
its seat, then turn the machine off and back on again. If the
problem persists, contact the Service provider.
Contact the service provider.
Turn the appliance off and back on again once only. If the
problem persists, contact the service provider.
9

HANDLING AND STORAGE

All the operations described in chapter 9
must be performed exclusively by the ser-
vice provider or specialised technician,
who shall organise all operating sequences and
employ suitable means to ensure strict compliance
with safety regulations in force.
9.1

Handling

During handling and transportation, the machine should
be kept in a vertical position, in accordance with the
instructions printed on the packaging.
Care should be taken during lifting and positioning.
Do not shake the machine.
During lifting and handling of the load, en-
sure that the surrounding area is free of
people, and in diffi cult conditions assign suitable
personnel to monitor all movements.
9.2

Storage

The machine should be stored in accordance with the
following conditions:
- minimum temperature: above 4°C.
- maximum temperature: below 40°C.
- maximum humidity: below 95%
The machine is packed in cardboard and expanded
polystyrene packaging.
Warning. Due to the total weight of the
packaged product, machines may not be
stacked higher than three units. The machine
should be stored in its original packaging, in a
place free from humidity and dust.
10

INSTALLATION

All the operations described in chapter
10 must be performed exclusively by the
service provider or specialised techni-
cian, who shall organise all operating sequences
and employ suitable means to ensure strict com-
pliance with safety regulations in force.
10.1

Safety regulations

• Read the entire instruction manual carefully.
• Connection to the power supply should be made in
compliance with the safety regulations in force in
the country where the machine is to be used.
• Connection to the drinking water network (for water
network machines) should be made in compliance
with the safety regulations in force in the country
where the machine is to be used.
• The socket to which the machine is connected must
be:
- compatible with the type of plug installed on the
machine;
- suitably sized to comply with the data on the pla-
te attached to the bottom of the appliance.
- connected to an effi cient earthing system.
• The power cord must not:
- come into contact with any type of liquid: danger
of electric shocks and/or fi re;
- be crushed and/or come into contact with sharp
surfaces;
- be used to move the machine;
• 33 •