Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Frame Rail
http://www.horizonglo
bal.com/
Bulk Head
and Bolt Plate
Centerline of
3"
Lower Fascia
5"
Vehicle Forward
Figure 3
1.
Remove Plastic Cover- (Driver Side) using a 10mm socket remove (4) nuts and using a flathead screwdriver remove (3) plastic push pins.
2.
Remove Lower Fascia- using a phillips-head screwdriver remove(2) screws (1) per side and using a flathead screwdriver remove (3) plastic push pins. Then remove the plastic fascia attachment with a
phillips-head screwdriver (1) screw per attachment and return to owner. (see figure 4)
3.
Lower Exhaust – using a exhaust hanger removal tool remove the rubber isolators from the hanger. NOTE: Support the exhaust before lowering.
Note: Removal of the heat shield is not required but can be removed to assist with modification. Cut or bend the area around the rearmost stud to make clearance for the hitch. Make sure to leave the hole in
the heat shield so that it may be reattached. If removed modify and reattach. (See figure 5)
4.
Remove Existing Hardware – Remove the existing 10mm bolts (2) each side from the bulk head.
j
k
5.
Fish Wire – Attach items
and
to item
and return to owner.
6.
Raise Hitch – Raise hitch into position, be careful not to push the hardware into the frame. Using the existing 10mm bolts (2) per side attach the hitch to the bulk head. Then remove item
l
m
j
item
and
to item
.
7.
Trim Lower Fascia- In the center of the lower fascia cut a 3 inch wide by a 5 inch long section to give clearance for the receiver tube of the hitch (see figure 3)
8.
Reinstall Lower Fascia and Plastic Cover- Snap the lower fascia into to place and reinsert the (2) screws removed in step 2. Then reinstall the plastic cover with the (4) 10mm nuts and (3) plastic push pins
removed in step 1.
9.
Torque Hardware-
Tighten all 10mm fasteners to 42 Lb.-Ft. (57 N*M) and all 7/16 fasteners to 50 Lb.-Ft. (68 N*M).
10. Raise Exhaust- Raise the exhaust back into position by reattaching the rubber isolators to the hangers.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2017 Horizon Global™ Corp. - Printed in Mexico
Installation Instructions
PART NUMBERS: 24964, 77964, CQT24964
①
Access
②
Hole
③
④
Existing 10mm
Bolt
Figure 1
n
and follow the instructions in figure 2. Leave item
n
A. Insert bolt and
B. Align block on
C. Pull bolt
access hole
Block into frame
Figure 2
Remove plastic
attachments (3)
Figure 4
Access
Hole
Bulk Head
and Bolt Plate
Existing 10mm Bolt
n
attached until the hitch is raised into position. NOTE: If plastic caps are covering the access hole remove
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 3 of 18
Fastener Kit: 24964F
①
Qty. (2)
Carriage bolt
7/16-14 x 1.75 GR5
②
Qty. (2)
Block
.250 x .875 x3
P/N – HE-2370-000
③
Qty. (2)
Conical washer
7/16"
P/N - 01292007
thru block
④
Qty. (2)
Het Nut
7/16 -14 GR2
⑤
Qty. (2)
Fish Wire
7/16"
P/N - 5481
Authorized Drawbar Kit:
Frame Rail
①
3593
(Sold Separately)
②
Drawbar must be used in the
RISE position only.
2"
③
④
Figure 5
4"
24964NP
07-24-17
Hole for
attachment stud
Bend or Trim
n
and attach
Rev. A
Publicidad
