Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
VENTILACIÓN EXTERIOR TRASERA
C
VISIÓN GENERAL DE LA
INSTALACIÓN
C1. Prepare la Pared Trasera
C2. Adjunte la Placa de Montaje
a la Pared
C3. Prepare el Gabinete Superior
C4. Ajuste el Calentador
C5. Monte el Horno Microondas
PREPARACIÓN DE LA PARED
C1
TRASERA PARA EL ESCAPE
EXTERNO TRASERO
Es necesario cortar una abertura en la pared trasera del
escape externo.
• Lea las instrucciones sobre la PLANTILLA DE LA
PARED TRASERA.
• Pegue la misma a la pared trasera, alineándola con
los agujeros previamente perforados A y B en la
placa de montaje.
• Corte la apertura, siguiendo las instrucciones de la
PLANTILLA DE LA PARED TRASERA.
20
Instrucciones de Instalación
(Conducto Horizontal)
3/8" TO EDGE
OPTION 2
STEP 1:
Installer uses bracket to make 2 marks. First
OPTION 1
12"
Second mark is made on the ouside edge of bracket.
mark is made by using the stampled slot in bracket.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
F. CUT OUT FOR HORIZONTAL
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
4"
OUTSIDE EXHAUST
Horizontal line
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
1. Use a level to check that the template is positioned
outlet.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
STEP 4:
accurately.
even with
here,
Make a mark
inside bottom of the
Make a mark here, along
2. Locate and mark at least one stud on the left or
stamped
bottom of
stamped slot provided.
NOTE:
right side of the centerline.
slot
screw mounted firmly in a stud to support the weight
It is important to use at least one wood
STEP 2:
of the microwave. Mark two additional, evenly spaced
the cabinets and makes 2 more marks. Marks are the
Installer moves bracket to the other side of
locations for the supplied toggle bolts.
same as STEP 1, just opposite side.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
4. Remove the template from the rear wall.
AT THIS TIME.
5. Review the Installation Instruction book for your
installation situation.
Make a
inside bottom of the
Make a mark here, along
mark here,
even with
bottom of
Darle vuelta a la hoja para consultar la
stamped slot provided
(same as Step 1).
slot
stamped
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTES:
30" MINIMUM WIDTH REQUIRED
- 13" Max Cabinet Depth
Locate and mark holes to align with holes in the
- 15" deep cabinets require additional steps using
mounting plate.
an additional installation kit: JX36BUMP
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
REAR WALL TEMPLATE
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Trim the rear wall template along the dotted line.
A
C
D
B
C2
ADHIERA LA PLACA DE
Adhiera la placa a la pared usando tornillos con resortes.
Por lo menos un tornillo de madera deberá ser usado
para adherir la placa al montaje de pared.
1
Retire las tuercas mariposa de los tornillos.
Inserte los tornillos en la placa de montaje a través
2
de los agujeros designados para entrar en la placa de
yeso y vuelva a ajustar las tuercas mariposa a 3/4"
sobre cada tornillo.
Para usar tornillos con resorte:
Espacio para Tornillos con Resorte
Superior al Grosor de la Pared
Tuercas Mariposa
Placa de
Tornillo con
Montaje
Resorte
Pared
Coloque la placa de montaje contra la pared e inserte
3
las tuercas mariposa en los agujeros de la pared para
montar la placa
PRECAUCIÓN
Tenga cuidado para evitar
pellizcos en los dedos entre la parte trasera de la placa
de montaje y la pared.
4
Ajuste todos los tornillos. Empuje la placa hacia afuera
de la pared para ayudar a ajustar los tornillos.
Extremo del Tornillo
31-7000110 Rev. 1
Publicidad
Tabla de contenido
