Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
MARKING THE MOUNTING HOLES
D
OPTION 1: USE PAPER REAR WALL TEMPLATE
CAUTION
Wear gloves to avoid cutting fingers on
sharp edges.
WARNING
Risk of electric shock. Can cause injury
or death. Take care to not drill into electrical wiring inside
walls or cabinets.
This Rear Wall Template serves to locate the mounting
holes for the bottom mounting plate and to locate the
horizontal exhaust outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or right side
of the centerline.
NOTE: It is important to use at least one wood screw
mounted firmly in a stud to support the weight of the
microwave.
31-7000110 Rev. 1
Installation Instructions
30"
OPTION 1
12"
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
F. CUT OUT FOR HORIZONTAL
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
4"
OUTSIDE EXHAUST
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
right side of the centerline.
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
30" MINIMUM WIDTH REQUIRED
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
REAR WALL TEMPLATE
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
A
C
3/8" TO EDGE
OPTION 2
NOTE: Refer to step C "DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET on page 10 for aligning instructions.
STEP 1:
Installer uses bracket to make 2 marks. First
STEP 3:
Installer uses a level to draw a horizontal line
mark is made by using the stampled slot in bracket.
that connects the two marks made with the stamped
Second mark is made on the ouside edge of bracket.
slot in the bracket.
Horizontal line
Make a mark
Make a mark here, along
here,
STEP 4:
even with
inside bottom of the
Installer uses marks to install bracket in
bottom of
stamped slot provided.
correct position. The bracket is to be installed per
stamped
standard requirements (at least one wood screw
slot
mounted in a stud, two additional evenly spaced
locations for toggle bolts). Mark hole location A,B, C and
D by placing the mounting bracket on the wall as shown
in the picture. Hole C and or D must be in a WALL STUD.
STEP 2:
Installer moves bracket to the other side of
the cabinets and makes 2 more marks. Marks are the
same as STEP 1, just opposite side.
Mark hole locations for A, B, C, and D.
B
D
C
Place bracket within the lines created in previous steps.
Make a
mark here,
Make a mark here, along
STEP 5:
Set mounting bracket aside and drill holes at
inside bottom of the
even with
bottom of
all marked locations. If there is a stud, drill a 3/16" hole
stamped slot provided
stamped
for wood screws. For holes that do not line up with a
(same as Step 1).
slot
stud, drill a 5/8" hole for a toggle bolt.
NOTES:
- 13" Max Cabinet Depth
- 15" deep cabinets require additional steps using
an additional installation kit: JX15BUMP
C
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
B
AREA.
3. Mark the hole location on the wall using the template at
holes A and B. Mark at least one hole location in area C
that lines up with the location of a stud. A minimum of
three holes must be used for mounting.
4. Drill holes in the marked locations. Where there is a stud,
drill a 3/16" hole for wood screws. For holes that do not
line up with a stud, drill 5/8" holes for toggle bolts.
NOTE: DO NOT INSTALL THE MOUNTING PLATE AT THIS
TIME
5. Remove the template from the rear wall.
A
9
Publicidad
Tabla de contenido
