Operation And Maintenance; Technical Parameters - GRAPHITE 58G014 Manual De Instrucciones

Batteries heat up when charging. Do not operate just
after charging – wait for the battery to cool down to room
temperature. It will prevent battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with signalisation of the battery level (3
LED diodes) (11). To check battery level status, press the button
for battery level indication (10) (fig. C). When all diodes are lit,
the battery level is high. When 2 diodes are on, the battery is
partially discharged. When only one diode is lit, the battery is
discharged and must be recharged.
CHOOSING SANDING PAPER
Coarse-grained sanding paper is used for coarse processing of most
materials, while fine-grained paper is used for finishing works.
• When the surface is not flat, start the work with coarse-grained
sanding paper and continue until the surface is flat.
• Next use middle-grained paper to remove traces of coarse
processing.
• To finish the work use fine-grained sanding paper.
INSTALLING SANDING PAPER
The orbital sander is equipped with pad with hook-and-loop
fastener. Use only appropriate sanding paper (perforated).
• Put the sanding paper close to the sander backing pad (5).
• Place the sanding paper so its holes (a) match holes on the sander
backing pad.
• Press the sanding paper against the backing pad (5) (fig. D).
• Ensure that the holes on the sanding paper and backing pad fully
match; it ensures sufficient dust extraction.
DUST EXTRACTION
Equipment of orbital sander includes dust bag (3) to maintain the
processed surface clean.
• Slide the dust bag (3) fastening onto dust extraction outlet (4)
(fig. E).
• When the dust bag is full, empty it to a special container.
• Reinstall the dust bag on the dust extraction outlet.
• Make sure the dust bag is securely fastened on the outlet.
Emptying the bag when it is half-full is recommended.
DUST BAG EMPTYING
The dust bag is placed on the plastic casing. Slightly turn the rear
ring counter-clockwise and slide it off from the back plastic casing to
empty the dust bag (fig. F). Remove the contents from the dust bag.
Installation of the dust bag is similar to removal, only the sequence
of actions is reversed.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The orbital sander features 3 gears (ranges of rotational speed).
Subsequent pressing of the switch button cycles between
rotational speeds.
Switching on:
Press the switch button (2) – the sander starts operation at the
maximum rotational speed.
Next press of the switch button – the sander operates at the
moderate rotational speed.
Next press of the switch button – the sander operates at the lowest
rotational speed.
Switching off:
Press the switch button (1) (fig. G).
Regardless of the gear the sander operates when switched off,
after it is switched on again, it starts operation at the highest
speed and cycles 3-2-1 (from the highest to the lowest rotational
speed, as described above).
ORBITAL SANDER OPERATION
• Whole area of the backing pad must rest on the processed surface.
• Turn the sander on, select appropriate rotational speed and
apply moderate pressure; move it along the processed material in
circular movements, in transverse or lengthwise direction.
• For coarse processing use sanding paper with coarse grain, for
finishing processing use fine-grained paper. It is best to match the
type of sanding paper by trials and errors.
• To end polishing, reduce pressure, lift the sander above the
processed surface and only then you can switch off the tool.

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a dry cloth or blow through with compressed
air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
REPLACEMENT OF BACKING PAD
Damaged backing pad (5) must be replaced immediately.
• Unscrew the screws that fix the backing pad (5).
• Remove and replace the backing pad.
• Tighten the fixing screws.
All defects should be repaired by service workshop authorized
by the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless Orbital Sander
Parameter
Battery voltage
Range of idle rotational speed
Range of Idle oscillation speed
Oscillation amplitude
Pad dimensions
Size of sanding paper
Protection class
Weight
Year of production
14
Value
18 V DC
5000/7000/9000 min
-1
10000/14000/18000 min
-1
2,7 mm
125 mm
125 mm
III
1,135 kg
2020