Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT:
a_
d_us_ _he Doos
Your refrigerator
has two adjustable,
front leveling
screws - one
on each side of the refrigerator
base. If your refrigerator
seems
unsteady
or you want the door to close easier, use the
instructions
below.
Before
moving
the refrigerator,
raise the leveling
screws so the
front rollers are touching
the floor.
Remove the base grille.
Grasp
the grille firmly
and pull it
toward
you.
2.
Raise or lower the cabinet.
Using a 1/4" hex driver, turn the leveling
screw on each side to
raise or lower that side of the refrigerator.
NOTE: Having
someone push against
the top of the refrigerator
takes some weight
off the leveling
screws. This makes it easier
to turn the screws. It may take several
turns of the leveling
screw to adjust the tilt of the refrigerator.
•
To raise, turn the leveling
screw clockwise.
•
To lower,
turn
the
leveling
screw
counterclockwise.
1.
Turn off the ice maker
by opening
the freezer
door and lifting
up the wire shutoff
arm as shown.
2.
Install the interior
water filter.
The interior
water
filter
mounting
bracket
is located
on the left side wall of the refrigerator
compartment.
Do not use with water that is microbiologically
unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Remove blue bypass cap and retain
for later use.
Gently
remove the interior
water
filter
from its packaging.
Remove the sealing
label from the end of the filter
and
insert it into the filter
head.
Gently
rotate
the filter
clockwise
until it stops. Then snap
the filter cover closed.
0
A.
leveling
screw
3.
Open
the door again
to make sure that it closes as easily as
you like. If not, tilt the refrigerator
slightly
more to the rear by
turning
both leveling
screws clockwise.
It may take several
more turns, and you should turn both screws the same amount.
4.
Replace
the base grille.
Please read before
using the water
system.
IMPORTANT:
After connecting
the refrigerator
to a water source or
replacing
the water
filter, follow
the steps below
to make sure that
the water
system is properly
cleaned.
This will flush air from the
filter and water
dispensing
system, and prepare
the water
filter for
use.
3.
4.
5.
Press the Water
button
on the dispenser
control
panel.
Use a
sturdy container
to depress
and hold the dispenser
lever for
5 seconds, then release it for 5 seconds.
Repeat
until water
begins
to flow. Once water
begins to flow, continue
depressing
and releasing
the dispenser
lever (5 seconds on, 5 seconds off)
until a total of 4 gal. (15 L) has been dispensed.
This will flush
air from the filter
and water
dispensing
system, and prepare
the water
filter for use. Additional
flushing
may be required
in
some households.
As air is cleared
from the system, water
may
spurt out of the dispenser.
NOTE:
After 5 minutes of continuous
dispensing,
the dispenser
will stop dispensing
water
to avoid flooding.
To continue
dispensing,
remove
the container
and press the dispensing
lever
again.
Inspect the filter system for water
leaks. If you see water
leaks,
see the "Troubleshooting"
section.
Turn on the ice maker
by opening
the freezer
door and
lowering
the wire shutoff
arm as shown. Please refer to the "Ice
Maker"
section for further
instructions
on the operation
of your
ice maker.
•
Allow
24 hours to produce
the first batch of ice.
•
Discard the first three batches
of ice produced.
11
Publicidad
