Descargar Imprimir esta página

Tools Needed - Sears Kenmore 106.7200 Manual De Uso Y Cuidado

Publicidad

Idiomas disponibles

Idiomas disponibles

TOOLS N EEDED:
5/_6",
3/8",
1/_"
hex head socket wrenches,
Torx ®t
T20 screwdriver,
#2 Phillips screwdriver,
and a flat-blade
screwdriver.
1.
Unplug
refrigerator
or disconnect
power.
2.
Keep the refrigerator
doors closed
until you are ready
to lift
them free from the cabinet.
NOTE:
Provide additional
support
for the refrigerator
door
while the hinges are being removed.
Do not depend
on the
door gasket
magnets
to hold the door in place while
you are
working.
3.
4.
Starting
with the right-hand
side door, remove
the parts for the
top hinge as shown in Top Hinge graphic.
Lift the refrigerator
door from the bottom
hinge pin.
Before
removing
the left-hand
side door, disconnect
the wiring
plug located
on top of the top hinge by wedging
a flat-blade
screwdriver
or your fingernail
between
the two sections.
See
Wiring
Plug graphic.
NOTE:
The green, ground
wire remains attached
to the hinge.
5.
Remove the parts for the top hinge as shown in Top Hinge
graphic.
Lift the left-hand
side door from the bottom
hinge pin.
Replace Doors and Hinges
1.
2.
3.
Assemble
the parts for the top hinge as shown in Top Hinge
graphic.
Do not tighten
the screws completely.
Replace
the parts for the bottom
hinge as shown in Bottom
Hinge graphic.
Tighten
screws. Replace the refrigerator
door.
NOTE:
Provide additional
support
for the refrigerator
door
while the hinges are being moved.
Do not depend
on the door
gasket
magnets
to hold the door in place while you are
working.
Align
the door so that the bottom
of the refrigerator
door
aligns evenly
with the top of the freezer
drawer.
Tighten
all
screws.
4.
Reconnect
the wiring
plug on top of the left-hand
side
refrigerator
door.
5.
Replace
the top hinge covers.
Remove
and
Replace
Freezer
Drawer
Front
IMPORTANT:
Two people
may be required
to remove
and replace
the freezer drawer
front. Graphics
are included
later in this section.
Remove
Drawer
Front
1.
Open
the freezer
drawer
to full extension.
2.
Loosen the four screws attaching
the drawer
glides to the
drawer
front. See Drawer
Front Removal
graphic.
NOTE:
Loosen screws three to four turns. Keep the screws in the
drawer
front.
3.
Lift drawer
front upward
and off the screws. See Drawer
Front
Removal
graphic.
Replace
Drawer
Front
1.
Slide the drawer
glides out of the freezer
compartment.
Insert
the screws in the top of the drawer
front
into the slots in the
drawer
brackets.
See Drawer
Front Replacement
graphic.
2.
Pull the drawer
brackets
toward
you to position
the two screws
in the bottom
of the drawer
front into the brackets.
See Drawer
Front Replacement
graphic.
3.
Completely
tighten
the four screws.
Final Steps
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1.
Plug into a grounded
3 prong outlet.
2.
Return all removable
door parts to doors and food
to
refrigerator.
t®TORX
is a registered trademark
of Saturn Fasteners, Inc.

Publicidad

loading

Este manual también es adecuado para:

Kenmore 106.7201