Safety Instructions; Use And Operation - Luna 20811-0106 Manual Del Usuario

ENGLISH ENGLISH
1
2
1. Pump lever 1. Pump lever
2. Foot pedal 2. Foot pedal
3. Swiveling wheel

1. SAFETY INSTRUCTIONS

1.1 The load to be lifted should never exceed the rated capacity
of the jack.
1.2 Never operate the jack beyond its maximum stroke indica-
ted on the label.
1.3 Park the vehicle or load to be lifted on a flat firm surface
and place wedges under the wheels to stop movement.
1.4 Position the jack on a solid, even and horizontal surface, ne-
ver use the jack on a slope.
1.5 The jack should be positioned so as to avoid the user from
having to operate it under the vehicle. Every vehicle lifted
by a jack should always have a secondary safety support,
such as mechanical stands.
1.6 Never lift a person with this jack. Ensure that all persons
are out of the vehicle before jacking.
1.7 It is necessary that the operator can watch the lifting device
and the load during all movements.
1.8 Before using the jack, make sure that the vehicle is free of
passengers, handbrake engaged and the engine is off.
1.9 Consult the vehicle handbook for jacking points.
6
5
4
3
4. Fixed wheel 4. Fixed wheel
5. Lifting arm 5. Lifting arm
6. Saddle
1.10 In the absence of jacking points the 1.10 In the absence of jacking points the trolley jacks should be
positioned under the centre of the load. Failure to position it positioned under the centre of the l
correctly may cause the load to be correctly may cause the load to be unbalanced, resulting in
possible equipment/load damage a possible equipment/load damage and operator injury.
1.11 It is imperative that all possible p 1.11 It is imperative that all possible precautions are taken to
avoid unexpected movement of th avoid unexpected movement of the vehicle load when it is
being lifted. being lifted.
1.12 The jack is a lifting device only and should never be used to 1.12 The jack is a lifting device only and s
move the vehicle or load. move the vehicle or load.
1.13 If these basic rules are not followed, injury to the user, the 1.13 If these basic rules are not followed
jack or the load being lifted may res jack or the load being lifted may result.
1.14 As an additional safety feature the jack is equipped with a 1.14 As an additional safety feature the
valve to prevent the unit from being valve to prevent the unit from being overloaded. This unit is
factory set and must not be tampere factory set and must not be tampered with.

2. USE AND OPERATION

2. USE AND OPERATION A A
2.1 2.1 Insert the handle into the socket and tighthen the screw . Insert the handle into the socket and
2.2 2.2 Before using the jack, it is necessary to purge air from the Before using the jack, it is necessar
valve system. This is carried out by valve system. This is carried out by pulling the handle up
and turning the handle clockwise. Whilst held in this posi- and turning the handle clockwise. W
tion, pump the jack several times. Release the handle and it tion, pump the jack several times. R
will automatically return back to the initial position ("Dead will automatically return back to th
man" principle ).The jack is now ready to be used. man" principle ).The jack is now read
2.3 2.3 These jacks are fitted with a foot pedal that gives a faster These jacks are fitted with a foot p
approach to the load. approach to the load.
2.4 2.4 To lower the load, turn the handle slowly clockwise. Our To lower the load, turn the handle
jacks are fitted with a safety device t jacks are fitted with a safety device that only permits the lo-
ad to be lowered smoothly by automatically controlling the ad to be lowered smoothly by auto
speed at a rate dependant upon the size of the load ( L.C.S.). speed at a rate dependant upon the
2.5 2.5 After use, make sure the lifting beam After use, make sure the lifting beam is fully retracted.
3. MAINTENANCE
3.1 Lubricate all moving parts at regular intervals.
3.2 Always keep the jack clean and protected from aggressive
conditions.
3.3 If you have to replace the oil, the correct volume is indica-
ted in the parts list. Make sure the piston is fully retracted.
IMPORTANT: An excess of oil will render the jack inope-
rative.
3.4 Use only hydraulic oil, type HL or HM, with an ISO grade
cinematic viscosity of 30 cST at 40ºC or an Engler viscosity
of 3 at 50 º C.
VERY IMPORTANT
3.5 When ordering spare parts, please make note of the part re-
ference as shown in the exploded view drawing provided. A
repair kit is available containing all the common spare
parts.
4. REPAIR
Both maintenance and repair must only be carried out by qualified
and approved personnel.
7
: Never use brake fluid.