LiftMaster LM3800W Manual Del Usuario página 12

Tabla de contenido

Idiomas disponibles

MyQ

MyQ allows you to control your garage door opener from your mobile device or computer from anywhere. MyQ technology uses a radio signal to

provide two way communication between the garage door opener and MyQ enabled accessories. The garage door opener has an internal gateway

that allows the garage door opener to communicate directly with a home Wi-Fi

INFRARED PHOTOCELLS

When properly connected and aligned, the infrared photocells will detect an obstruction in the path of the infrared beam. If an obstruction breaks the

infrared beam while the door is closing, the door will stop and reverse to full open position, and the opener lights will flash 10 times. If the door is fully

open with infrared photocells installed, and are misaligned, the door will not close from a remote control. However, you can close the door if you hold

the button on the door control or keyless entry until the door is fully closed. The infrared photocells do not affect the opening cycle.

ENERGY CONSERVATION

For energy efficiency the garage door opener will enter sleep mode when the door is fully closed. The sleep mode shuts the garage door opener

down until activated. The sleep mode is sequenced with the garage door opener light; as the light turns off the sensor LEDs will turn off and when-

ever the garage door opener lights turn on the sensor LEDs will light. The garage door opener will not go into the sleep mode until the garage door

opener has completed 5 cycles upon power up.

LIGHTS

The garage door opener light will turn on when the opener is initially plugged in; power is restored after interruption, or when the garage door opener

is activated. The light will turn off automatically after 4-1/2 minutes.

LIGHT FEATURE

The garage door opener is equipped with an added feature; the lights will turn on when someone enters through the open garage door and the

infrared beam is broken. Infrared photocells 771EV / 772E / 771EVK / G770E need to be installed to enable this feature.

BATTERY BACKUP (OPTIONAL)

The battery backup system allows access in and out of your garage, even when the power is out. When the garage door opener is operating on bat-

tery power, the garage door opener will run slower, the light will not function, the Battery Status LED will glow solid orange, and a beep will sound

approximately every 2 seconds.

USING YOUR GARAGE DOOR OPENER

The garage door opener can be activated through a wall-mounted door control, remote control, wireless keyless entry or MyQ accessory. When

operating the door opener by radio control or wall switch:

•

closes the door when it is fully open

•

opens the door when it is fully closed

•

stops the door if it is opening or closing

•

the door moves in the opposite direction to the last completed move,

if it is partially open If the door senses an obstruction or is interrupted while opening the door will stop. If the garage door opener senses an obstruc-

tion while closing, the door will reverse. If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times. However, you

can close the door if you hold the button on the door control or keyless entry until the door is fully closed. The infrared photocells do not affect the

opening cycle.

CYCLE COUNTER.ACTIVATION AND READING PROCEDURE:

1. Disconnect power from RJO to enter into this mode.

2. Press the Adjustment (A) and Learn buttons (L) and hold together upon restoring power.

3. Operator "UP" arrow button (U) LED will flash ONE time for each thousand FULL cycles completed as long as the Adjustment (A) and Learn

buttons (L) are pressed and held.

For example, if the RJO has made 8756 cycles, UP LED shall blink 8 times.

To repeat the read out, disconnect RJO from power and start again.

Light transmitter (with 78EV): Enables learning a transmitter to the MyQ Remote via Multifunction wall control.

To programm transmitter to MyQ Remote LED Light:

1. Press and hold the LIGHT & LOCK button together.

2. While holding above both buttons, press & hold one of the button on transmitter until RJO WorkLight flashes once.