Troubleshooting - Anest Iwata ICON-M233N Manual De Instrucciones De Uso

iCon-M233N
Multi Spray Unit |
13. TROUBLE SHOOTING
INCONVENIENCE CAUSE
The ball valve is not in
a
the proper position.
The air regulator is not
b
The air pressure
open.
1
does not increase
c Insufficient air pressure.
Clogged paint filter or
a
paint circuit.
The paint does
2 not flow out of
the gun
b Clogged nozzle.
c Jammed safety stop.
The air does not supply
a
the pump.
The pump has a tech-
b
nical problem.
The pump does
3
not work
The pump does Some air got inside the
4 a
not stop.
paint ducts.
22
iCon-A233N
Airless Unit
CHECK SOLUTION
Make sure the ball valve Adjust the ball valve in the pro-
a a
is in the proper position. per position.
Check the proper fun-
If it is closed, open it.
b b
ctioning of the air re-
If it is damaged, replace it.
gulator.
Check the proper fun- If the compressor does not
ctioning of the ma- supply enough air pressure,
c c
nometer of pressure replace it with one of greater
gauge. capacity.
The paint circuit is obstructed
Opening the drain val- from the pump inlet to the fluid
a ve, the paint does not a pipe fitting. Check for the ob-
flow out. structed point and remove the
clogging materials from circuit.
The paint course, from fluid
hose fitting to the gun nozzle,
is blocked. Check for the ob-
Opening the drain val- structed point and remove the
ve, the paint flows out clogging; this inconvenience
a1 a1
regularly, but not when is usually caused by the ob-
pulling the gun trigger. struction of the gun filter.
*Refer to the instruction ma-
nual of spray gun.
Remove the nozzle and
pull the trigger of the Refer to the instruction manual
b gun. If the paint flows b of spray gun, about trouble-
out it means that the shooting reference.
nozzle is clogged.
c
Unlock the safety valve.
Check the air supply
a a Replace it if spoilt or clogged.
hose.
Separate the air mo-
If the motor is running proper-
tor from the pumping
ly, follow the instructions pro-
b b
group and test it using
vided in the solution column,
a different air supply
point 2 (a-b).
hose.
If the motor is not running pro-
perly, disassemble the cylinder
and inspect it.
c
In case of special anomalies,
ship it to our Customer Care
Technical Service.
Make sure the dip tube
a a
Tighten suction hose fitting.
is properly connected.
iCon-M233N
Multi Spray Unit |
13. TROUBLE SHOOTING
INCONVENIENCE CAUSE
Some air remains inside
b
the paint ducts.
Seats and balls (inside
c the fluid pump) are dirty
The pump does
or damaged.
4
not stop
The V-packings (inside
d the fluid pump) are dirty
or damaged.
Leakage from the paint
e
ducts.
The drain valve is not
f
closed.
The V-packings (inside
a
the fluid pump) are dir-
ty or damaged.
The spray-fan
Seat and ball (inside the
5 size keeps chan-
b fluid pump) are dirty or
ging
damaged.
Spray gun nozzle, worn
c
out.
Paint filter of paint cir-
d
cuit clogged.
The indicator of
pressure gauge
indicates the pre-
6 sence of pressure a Damaged air regulator.
even though the
air regulator is
closed.
iCon-A233N
Airless Unit
CHECK SOLUTION
If the paint is in standard
condition increase its le-
Make sure the paint is in
vel at least until it fully co-
good condition and that
vers the suction hose set.
b the suction hose set is b
Then, carry out the start-
fully immersed in the
up operations relative to
product to be pumped.
the release of air from the
paint ducts.
Clean them if they are
enclosed with solidified
Disassemble the fluid
paint residues.
c pump and check the c
Otherwise, if they are
seat and ball conditions.
irreparably worn out, re-
place them.
Clean them if they are
enclosed with solidified
Disassemble the fluid
paint residues.
d pump and check the d
Otherwise, if they are
V-packings conditions.
irreparably worn out, re-
place them.
Inspect all the paint If any leakage is found,
e e
ducts. see to its fixing.
f Close the drain valve.
Clean them if they are
enclosed with solidified
Disassemble the fluid
paint residues.
a a
pump and check the
Otherwise, if they are
V-packings conditions.
irreparably worn out, re-
place them.
Clean them if they are
enclosed with solidified
Disassemble the fluid
paint residues.
b pump and check the b
Otherwise, if they are
seat and ball conditions.
irreparably worn out, re-
place them.
c
Replace it.
d
Refer to (2 - a).
a Replace it.
23