Transport And Handling; Handling And Storage - Anest Iwata ICON-M233N Manual De Instrucciones De Uso

iCon-M233N
Multi Spray Unit |
4. TECHNICAL DATA
VERSIONS
Plunger Pump:
Air Motor cylinder diameter:
Paint delivery filter
Paint filter:
Fluid suction filter
Max. fluid working pressure:
Max. air inlet pressure:
Pressure ratio:
Working temperature:
Noise level:
Air consumption
Max. fluid delivery
Fluid output:
Max. volume/min.
Max. No. of cycles per minute
Paint filter set
Wetted parts
Suction hose set
material:
Fluid pump
5. PRODUCT IDENTIFICATION
PLATE DATA: The manufacturer's identification data are applied on Multi Spray and Airless Units (see picture be-
low). They must not be delated at all, even if the equipment is resold. For any communication with the manufacturer
always mention the serial number written on the pump itself.
MODEL NAME
ICON PUMP 233N UNIT
MAX. AIR W.P.R.
RATIO
MANUFACTURED
Manufacturing date
ANEST IWATA Strategic Center
Via degli Aceri 1, Cardano al Campo
(VA) Italy
CE Marking - ATEX Marking
8
iCon-A233N
Airless Unit
ICON-M233N ICON-A233N
PP-3025N
100 mm
TF-1S (100 Mesh)
50 Mesh
210 bar (21 MPa)
7.0 bar (0.7 MPa)
30:1
5°~40° C
84.7 dB(A)
110 Nl/min. at 30 cyc/min.
25 ml
2.5 l/min.
100 cyc
Body: AISI303 - Filter: AISI304/Polyamide
Hose: Rubber - Pipe, Filter and Connection: AISI304
Mainly: AISI303 - PE - PTFE
Max. Working Pressure
0.7MPa/7.0bar/100psi
30:1 SERIAL NO. XE
2019
MADE IN ITALY
Serial Number
• Environmental limits:
II 2 G T 6 X
(ambient temperature 5°C ~ 40°C).
• Maximum superficial temperature:
Temperature class T6.
iCon-M233N
Multi Spray Unit |
6. BOX CONTENT
When receive and before using the Pump, make sure that it has not been damaged during transport or storage.
Also check that all the following standard components are inside the packaging.
MULTI SPRAY or AIRLESS UNIT, mounted on Cart Frame
Air regulator
for Airless Unit
*or
Hopper Set
(6lt.)
*or
Suction Hose Set
(50 Mesh)
Instruction Manual

6.1 TRANSPORT and HANDLING

To transport the equipment, only the systems described below can be used. In any case, make sure that the
transport and lifting device can bear the weight of the equipment with its packaging.
WARNING
ALWAYS KEEP THE PACKAGING IN VERTICAL POSITION.
IT IS ADVISABLE THAT THE STAFF IN CHARGE OF HANDLING THE EQUIPMENT WEAR
PROTECTIVE GLOVES AND SAFETY SHOES.
WHILE LIFTING OR HANDLING THE EQUIPMENT OR ANY OF ITS COMPONENTS CLEAR THE
WORKING AREA. LEAVE ALSO A SUFFICIENT SAFETY AREA AROUND THE EQUIPMENT TO
AVOID DAMAGING PEOPLE OR OBJECTS.

6.2 HANDLING and STORAGE

THE EQUIPMENT IS PUT INSIDE A CARDBOARD PACKAGING AND WRAPPED WITH SOME SHOCK-
PROOF MATERIAL.
WARNING
TO HANDLE THE CARDBOARD PACKAGING USE A TROLLEY.
FOLLOW THE INSTRUCTIONS ON THE PACKAGING BEFORE HANDLING AND OPENING IT.
DURING TRANSPORT AND STORAGE MAKE SURE THE TEMPERATURES BETWEEN 0 AND 40°C
ARE NOT EXCEEDED. IN CASE OF STORAGE, MAKE SURE THE EQUIPMENT IS NOT PUT IN
PLACES WITH AN EXCESSIVE HUMIDITY.
iCon-A233N
Airless Unit
MULTI SPRAY or AIRLESS UNIT,
mounted on Wall Bracket
Air regulator
for Multi Spray Unit
*or
Air regulator
for Airless Unit
Hex. Socket Screws
Suction Hose Set
M8x20
(50 Mesh)
(2 pcs.)
Instruction Manual
9