cleanAIR AerTEC SeeMAX Manual Del Usuario página 5

• After cleaning individual parts with a damp cloth, it is nece-
ssary to rub them dry or let them dry at room temperature.
• It is recommended to use CleanAIR® ®klar-pilot Fluids for ca-
ring for the visors and plastic parts.
DO NOT USE A DISHWASHER OR DRYER!
DO NOT USE ACETONE OR OTHER CLEANING SOLVENTS!
ADF Battery replacement
When the LOW BATTERY led starts glowing, replace the batte-
ries with their proper CR2032 equivalent.
4. Control
Headband adjustments (all products)
1. Head harness depth adjustment: Adjust the head harness
depth so, that the band part circulating the head is positio-
ned relatively low. This way welding helmet stays well on
the head. The sweatband should be a little above the ey-
ebrows. Depth of a head harness can be adjusted at its top.
2. Adjustment of welding helmet angle: Adjust the welding
helmet angle in regard to your face so that the lower edge
of welding the helmet is positioned near your chest in the
welding position. This way the welding helmet provides the
best protection.
3. Tension adjustment of the head harness: Adjust the band
tightness by rotating the adjusting wheel positioned in the
back of the band.
4. Adjusting the welding helmet resistance against vertical
rotation: Adjust the welding helmet's resistance against
vertical by turning the two screws on the sides. Adjust the
resistance so that the lifted helmet remains up, but drops
with a sharp nod. If the helmet hits the chest when nod-
ding, the setting is too loose.
5. Adjusting the nose distance: The distance between the
face and the ADF can be adjusted by loosening of the outer
screws and then moving forward or backward to the spe-
cified positions. Tighten the screws to secure the selected
position.
ADF settings for AerTEC™ RangeMAX:
Grinding Welding/grinding:
button
on/off
Welding mode is the default. Press the
„Grinding button" to switch the helmet to
a grinding mode. In this mode, the welding
filter remains in light condition for ten
minutes.
Sensitivity setting:
Use the sensitivity knob to set the ambient
light sensitivity. In the „Super High" area the
maximum light sensitivity can be achieved.
Delay settings:
The shown knob is for selecting the delay
of clearing the ADF after the welding arc
has extinguished. The knob allows for a
smooth setting of the un-dimming delay
between 0.1 and 2.0 s.
Odstín AUTO / Manual:
In "Manual" mode, protection levels 7-12 can be selected by
turning the protection level regulator.
In „AUTO" mode, the protection level is automatically set and
adjusted by a preset deviation. The absolute minimum and
maximum are protection levels 5 and 12; values outside this
the range are not possible.
M
A
ADF settings for AerTEC™ OptoMAX:
Welding/grinding:
Welding mode is the default. Press the
„Grinding button" to switch the helmet to
a grinding mode. In this mode, the welding fil-
ter remains in light condition for ten minutes.
Sensitivity setting:
Use the sensitivity knob to set the ambient
light sensitivity. In the „Super High" area the
maximum light sensitivity can be achieved.
Delay setting:
The opening knob allows selecting opening
delay from dark to light. The rotary knob
allows stepless setting from dark to light
between 0.1 and 2.0 s.
Shade AUTO / Manual:
In "Manual" mode, protection levels 5-13 can be selected by
turning the protection level regulator. In „AUTO" mode, the
protection level is automatically set and adjusted by a preset
deviation.
MODE
AUTO
AUTO
MANUAL
MODE
MAN RANGE
5 - 9
MAN
Outer lens cover exchange:
RangeMAX:
AerTEC™
M
A
MAN RANGE
9 - 13
OptoMAX:
AerTEC™
5