CST/BERGER LM800 Serie Manual Original página 31

Technical Data
Remote control
Article number
1)
Working range
Batteries
Weight according to
EPTA-Procedure 01/2003
1) The working range can be decreased by unfavourable envi-
ronmental conditions (e.g. direct sun irradiation).
Please observe the article number on the type plate of your
remote control. The trade names of individual remote controls
may vary.
For clear identification of your remote control, see the serial
number 40 on the type plate.
Assembly
Inserting/Replacing the Battery
Using alkali-manganese batteries is recommended for
operation of the remote control.
The remote control is provided with batteries inserted.
Before putting into operation for the first time, remove
the safety strip in the battery compartment ("Remove
before Use").
The batteries must be replaced when operation indi-
cator 32 no longer lights up after pressing any button
on the remote control.
To open the battery lid 39, press on the latch 38 and
remove the battery lid. Insert the batteries. When
inserting, pay attention to the correct polarity accord-
ing to the representation on the inside of the battery
compartment.
Always replace all batteries at the same time. Only use
batteries from one brand and with the identical capacity.
Remove the batteries from the remote con-
trol when not using it for longer periods.
When storing for longer periods, the batteries can
corrode and discharge themselves.
Operation
Initial Operation
Protect the remote control against moisture
and direct sunlight.
Do not subject the remote control to extreme
temperatures or variations in temperature.
As an example, do not leave it in vehicles for longer
periods. In case of large variations in temperature,
allow the remote control to adjust to the ambient
temperature before putting it into operation.
2 610 A15 117 • 12.8.09
RC700
F 034 K69 ANA
30 m
2 x 1.5 V LR06 (AA)
115 g
The remote control remains ready for operation as
long as batteries with sufficient voltage are inserted.
Set up the rotational laser in such a manner that the sig-
nals of the remote control directly reach one of the
receiption lenses on the rotational laser (for this, see
the operating instructions of the rotational laser). When
the remote control cannot be pointed directly against a
receiption lens, the working range is reduced. By
reflecting the signal (e.g. against walls), the working
range can be improved, even for indirect signals.
After pressing a button on the remote control, the illu-
minated operation indicator 32 indicates that a signal
was sent out.
Switching the rotational laser on/off with the remote
control is not possible.
Operating Modes
The shock-warning function and the on and off switch-
ing of the bottom plumb beam on the rotational laser
level cannot be remote controlled.
The function of the buttons on the remote control are
identical with the functions of the respective buttons
on the rotational laser level.
Example: Pressing the rotation operation button
switches the rotational laser level from line operation
to rotation operation. This happens no matter if you
press rotation operation button on the rotational laser
level or on the remote control.
For detailed information of the rotational laser level
functions, see the operating instructions of the rota-
tional laser level (see "Rotational Laser Level", from
page 20 on).
Rotation, Line and Point Operation (LM800DP)
By pressing the rotation operation button 45, you can
switch from line to rotation operation or decrease the
rotational speed in steps down to zero (point operation).
By pressing the line operation button 35, you can
switch from rotation to line operation or increase the
aperture angle in steps or decrease it to 0° (point
operation).
Switching Off the Automatic Levelling
By pressing button 43, the automatic levelling for both
the X- and Y-axis can be switched off.
To switch off the automatic levelling, the shock-warn-
ing function must be switched off on the rotational
laser level.
Rotating the Laser Point/Laser Line in the Rota-
tional Plane (LM800DP)
The laser point or the laser line can be rotated in steps
by 360° within the rotational plane. Press button 37
to rotate in clockwise direction, and button 42 to
rotate in anticlockwise direction. Pressing and holding
the buttons increases the speed of the rotation head
in the desired direction.
English | 31