Publicidad
CONNECTING TO THE
ANCHOR POINT
The snap hook can be
used to connect a fall
arrest system to an an-
chor device complying
with EN 795 standard
or to a structural fixed
CORRETTO
RIGHT
element situated above
the workplace, with a
min. static resistance of
15 kN.
The shape of the anchor
point should not let self-
acting disconnection of
the device.
ATTENTION: In order
to avoid any acciden-
tal opening of the snap
RIGHT
hook, always check that
the gate is protected
with the locking gear. The locking gear's right functioning can be guaranteed by the periodic lubrication of the snap hook's
movable parts, with silicon oil or a similar one.
The length of the snap hook should be taken into account when used in any fall arrest system as it could influence the length
of a fall.
NOTES
Before using a fall arrest system, of which the snap hook is a component, you have to check that all devices are correctly con-
nected. They can work without any trouble and they are certified with the obligatory standards:
- EN 353-1, EN 353-2, EN 354, EN 355, EN 360, EN 361, EN 362: for fall arrest system.
- EN 795: for anchor devices.
- EN 341: for descender devices.
USE
During use, the device should be protected from a contact with oils, acids, solvents, basics, open fire, hot metal drops and
sharp edges. You should avoid using the device in the dust laden and greasy environment.
WITHDRAWN FROM USE
The PPE must be withdrawn from use immediately when any doubt arises about its good condition or its right functioning.
Then it must be sent to the device manufacturer or to his certified representative to carry out a detailed inspection and to value
its eventual repair or destruction. If the PPE has been used to arrest a fall, it must be destroyed immediately.
PERIODIC REVIEWS
After each 12 months of utilization the PPE must be withdrawn from use for carrying out the periodic review.
During this inspection will be established admissible time for the PPE use till next periodic review. After this period, it is strictly
forbidden to use the PPE without carrying out next periodic review. All the information concerning the periodic review must be
recorded in the Identity Card. The periodic reviews and the updating of the Identity Card can be carried out by the manufac-
turer or by his authorized representative only.
ADMISSIBLE TIME OF USE
The expected average life of the PPE, if it is kept as specified in this informative note and it is subjected to all periodic reviews,
is 5 years from first use date.
THE ESSENTIAL PRINCIPLES OF USE OF PPE AGAINST FALLS FROM A HEIGHT
- PPE shall only be used by a person trained and competent in its safe use.
- PPE must not be used by a person with medical condition that could affect the safety of the equipment user in normal and
emergency use.
- A rescue plan shall be in place to deal with any emergencies that could arise during the work.
- It is forbidden to make any alterations or additions to the PPE without the manufacturer's prior written consent.
- Any repair shall only be carried out by the equipment manufacturer or his certified representative.
- PPE shall not be used outside its limitations, or for any purpose other than that for which it is intended.
- PPE should be a personal issue item.
- Before use ensure about the compatibility of items of equipment assembled into a fall arrest system.
- Periodically check connecting and adjusting of the equipment components to avoid accidental loosening or disconnecting
of the components.
- It is forbidden to use combinations of PPE in which the safe function of any items is affected by or interferes with the safe
function of another.
- Before each use of PPE it is obligatory to carry out a pre-use check of the equipment, to ensure that it is in a serviceable
condition and operates correctly.
- During pre-use check it is necessary to inspect all elements of the equipment in respect of any damages, excessive wear,
corrosion, abrasion, cutting or incorrect acting, especially take into consideration: in full body harnesses and belts: buckles,
adjusting elements, attaching points, webbings, seams, loops; in energy absorbers: attaching loops, webbing, seams, con-
nectors; in textile lanyards or lifelines or guidelines: rope, loops, thimbles, connectors, adjusting element, splices; in steel
lanyards or lifelines or guidelines: cable, wires, clips, ferrules, loops, thimbles, connectors, adjusting elements; in retract-
able fall arresters: cable or webbing, retractor and brake proper acting, casing, energy absorber, connector; in guided type
fall arresters: body of the fall arrester, sliding function, locking gear acting, rivets and screws, connector, energy absorber;
in connectors: main body, rivets, gate, locking gear acting.
cod. 121066 - mod. CM03
NON CORRETTO
WRONG
WRONG
- It is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller
shall provide instructions for use, for maintenance, for periodic examination and for repair in language of the country in
which the product is to be used.
- A full body harness conformed to EN 361 is the only acceptable body holding device that can be used in a fall arrest sys-
tem.
- There are many hazards that may affect the performance of the equipment and corresponding safety precautions that have
to be observed during equipment utilization, especially:- trailing or looping of lanyards or lifelines over sharp edges; any
defects like cutting, abrasion, corrosion; climatic exposure; pendulum falls; extremes of temperature; chemical reagents;
electrical conductivity.
- PPE can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile prod-
ucts use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned
only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry
naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can
be regularly slightly lubricated to ensure better operation. Other maintenance and cleaning procedures should be adhered
to detailed instructions stated in the manual of the equipment.
- PPE must be transported in its original package.
- PPE must be stored in their original packaging, in a well-ventilated place, protected from direct light, ultraviolet degrada-
tion, damp environment, sharp edges, extreme temperatures and corrosive substances.
- The PPE must be disposed of in compliance with the local regulations in force on this subject (dump, incinerator).
- In the case of manufacturing defects this PPE will be replaced.
It is the responsibility of the user organisation to provide the IDENTITY CARD and to fill in the details required. The identity
card should be filled in before the first use of the equipment. Any information about the protective equipment (device name,
serial number, date of purchase, date of first use, user's name, information about reviews and repairs) shall be noted in the
IDENTITY CARD. Do not use the PPE without the identity card duly filled in.
IDENTITY CARD
DEVICE NAME
SERIAL NUMBER
USER'S NAME
DATE OF PURCHASE
TECHNICAL INSPECTIONS
DATE
INSPECTION REASON
1
2
3
4
5
For more information, contact:
Registered Community Trade Mark, no 001240407 c/o UAMI - Alicante - Spagna
www.newtecsafety.com - info@newtecsafety.com - Factory: PL8310001653
cod. 121066 - mod. CM03
CODE
PRODUCTION DATE
DATE OF FIRST USE
DEFECTS NOTED, REPAIRS CARRIED OUT,
PERIODIC REVIEW NEXT
OTHER RELEVANT INFORMATION
DUE DATE
RESPONSIBLE
PERSON
SIGNATURE
Publicidad
