Positioning And Testing; Setting Operations; Aluminium Welding - STAYER WELDING PROGRESS 1700L Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

with one finger against solid 12.5 mm ø or larger foreign bodies.
The equipment is prepared for working within a temperature
range from -15ºC to 70ºC, taking into account the limitation of a
decrease in performance (duty cycle) as of ambient temperatures
above 40ºC.
4.- OPERATING INSTRUCTIONS

4.1.- Positioning and testing

All Steyer Welding machines of the series must be handled
using the handle which is arranged for transport.
A fee space of at least 15cm must be arranged around the
equipment, and free circulation of air must be secured for
correct heat dissipation. Before each work, good operation and
correct tightening of all external elements of the equipment shall
be verified: power supply plug, cable, housing structure and
connection terminals and switches.
4.2.- Tool changing
All Steyer Welding machines of the series have a 1/2 inch DINSE
quick connector for the welding cables. To remove or put the
connector on, it is sufficient to turn the connector a quarter turn
leftward or rightward.
WARNING: Always connect the DINSE connector as
far as it will go and make sure that the splice with the
cable is in a good condition and that the contact surface
is clean. A bad splice or a dirty connection will result in a bad
performance and make the front panel to become overheated,
fused or burnt.

ALUMINIUM WELDING

Thickness of
Tungsten
the piece to be
electrode
welded
diameter
mm
mm
0.6
1.0 - 1.6
1.0
1.0 - 1.6
1.5
1.0 - 1.6
2.5
1.6 - 2.4
3.0
1.6 - 2.4
4.0
2.4
5.0
2.4 - 3.2
6.0
2.4 - 3.2
8.0
3.2 - 4.0
ENGLISH
33
Amperage setting
Filler rod diameter
mm
0 - 1.0
0 - 1.6
0 - 1.6
1.6 - 2.4
1.6 - 2.4
1.6 - 2.4
2.4 - 3.2
2.4 - 3.2
3.2 - 4.0
33

4.3.- Setting operations

All Steyer Welding machines contain a complex electronic system
and come completely calibrated ex works, so that, for the sake
of efficiency and safety, it is not authorized to be manipulated by
the user. In case of any doubt regarding a malfunction, contact
your distributor or our helpdesk system.
4.4.- Limits regarding the size of the workpiece
The main restriction regarding the size of the workpiece is its
thickness which is limited by the power of the equipment. With
more power, you may carry out accurate welds (with suitable
penetration of the welding bead) in pieces having a higher
thickness. The following table may serve you as an orientation:
SHIELDED ELECTRODE WELDING
Thickness of
the piece to be
electrode
welded
diameter
1 a 2 mm
1,5 a 3 mm
2,5 a 5 mm
5 a 8 mm
8 a 12 mm
More than 12 mm
Argon gas flux
range
A
l/min
25 - 40
4 - 5
40 - 60
4 - 7
60 - 90
6 - 9
80 - 120
6 - 9
100 - 160
7 - 10
130 - 200
10 - 15
150 - 250
10 - 15
200 - 280
10 - 15
200 - 300
12 - 18
E6013
Amperage setting
range
1,6 mm
30 – 60
2,0 mm
50 – 70
2,5 mm
60 – 100
3,2 mm
85 - 140
4,0 mm
120 – 190
5,0 mm
180 – 240
Joint size
Joint shape
mm
1
1
1
1
1 - 2
2 - 3
2 - 3
3 - 4
4 - 5
a.b
a.b
b
b
b.c
c.d
c.d
c.d
d

Publicidad

Tabla de contenido
loading

Tabla de contenido