Water And Ice Dispensers - Sears Kenmore Elite 106.5177 Serie Manual De Uso Y Cuidado

Disabling Sounds
To turn off all dispenser and control sounds, press and hold WATER/
ICE and MEASURED FILL at the same time for 3 seconds.
IMPORTANT: To avoid unintentionally changing other settings, be sure
to press both buttons at exactly the same time.
To turn all sounds back on, press and hold WATER/ICE and
MEASURED FILL at the same time for 3 seconds again.

Water and Ice Dispensers

NOTES:
The dispensing system will not operate when either door (refrigerator
or freezer) is open.
Allow 24 hours for the refrigerator to cool down and chill water.
Allow 24 hours to produce the first batch of ice. Discard the first three
batches of ice produced. Wait 72 hours for full ice production.
The display screen on the dispenser control panel will turn off
automatically and enter "sleep" mode when the control buttons and
dispenser pad have not been used for 2 minutes or more. While in
"sleep" mode, the first press of a control button will only reactivate the
display screen, without changing any settings.
Flush the Water System
Air in the water dispensing system can cause the water dispenser to drip.
After connecting the refrigerator to a water source or replacing the water
filter, flush the water system. Flushing the water dispensing system forces
air from the water line and filter, and prepares the water filter for use.
NOTE: As air is cleared from the system, water may spurt out of the
dispenser.
1. Using a sturdy container, depress and hold the water dispenser pad
for 5 seconds, then release it for 5 seconds.
2. Repeat Step 1 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing the
dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal.
(12 L) has been dispensed.
Additional flushing may be required in some households.
Dispensing Options
Your dispenser can dispense water and ice in two ways.
The DISPENSE WATER button, located below the dispenser control
panel's display screen, dispenses only water.
The dispenser pad is the pad located along the rear wall of the
dispenser cavity. When pressed, it dispenses either water or ice,
depending on the chosen setting.
To dispense both water and ice at the same time, select the desired type
of ice and dispense it using the dispenser pad, then press the DISPENSE
WATER button while still dispensing ice.
Calibrate Measured Fill
Household water pressure may affect the accuracy of the Measured Fill
feature. For optimum performance of your water dispenser, you must first
calibrate Measured Fill.
IMPORTANT: Flush the water system before calibrating Measured Fill.
1. Place a sturdy measuring cup (1 cup [237 mL] size) on the dispenser
tray, centered in front of the water dispenser pad.
NOTE: Depending on your model, a measuring cup may be provided.
18
2. Press and hold the SETTINGS and LOCK buttons at the same time for
3 seconds. The words "Back" and "1 Cup" will appear on the display
screen. Also, "CALIBRATION" will illuminate and remain lit while the
Measured Fill feature is being calibrated.
NOTE: You may press the WATER/ICE button under the word "Back"
at any time to exit calibration mode. The display screen's
"CALIBRATION" text will turn off.
3. Using your hand (not the measuring cup), press and release the water
dispenser pad in order to dispense water to the 1 cup fill line.
NOTE: If overfilling or spilling occurs, discard the water and press
"Back" to restart the calibration process.
4. When 1 cup of water has been correctly dispensed into the measuring
cup, press the MEASURED FILL button under the word "Confirm" to
confirm the calibration.
When Measured Fill calibration has been confirmed, the display will return
to the home screen.
The Water Dispenser
IMPORTANT:
Dispense at least 1 qt (1 L) of water every week to maintain a fresh
supply.
If the flow of water from the dispenser decreases, it could be caused
by low water pressure.
With the water filter removed, dispense 1 cup (237 mL) of water. If
1 cup of water is dispensed in 8 seconds or less, the water pressure
to the refrigerator meets the minimum requirement.
If it takes longer than 8 seconds to dispense 1 cup of water, the
water pressure to the refrigerator is lower than recommended. See
"Water Supply Requirements" or "Problem Solver" for
suggestions.
To Dispense Water (Standard):
NOTE: While dispensing water and for 3 seconds after dispensing has
stopped, the digital display will show how much water has been dispensed.
The default unit is ounces. To switch to cups or liters, press the SETTINGS
button, then press MEASURED FILL to toggle through the available units.