Publicidad
Idiomas disponibles
Idiomas disponibles
CEBORA S.p.A.
4.2
Technical specifications.
The Power Source is built according to the
following international standards:
IEC 60974-1 / IEC 60974-5 / IEC 60974-10 (CL . A);
IEC 61000-3-11 / IEC 61000-3-12 (see note at the
paragraph end).
N°.
Serial number. Must be indicated on
any request regarding the Power
Source.
Three-phase
converte
r
Transformer - rectifier.
MIG Suitable for MIG/MAG welding.
MMA Suitable for welding with covered
electrodes.
TIG Suitable for TIG welding.
U0.
Secondary open-circuit voltage.
X.
Duty cycle percentage. The duty
cycle expresses the percentage of 10
minutes during which the Power
Source may run at a certain current
without overheating.
I2.
Welding current.
U2.
Secondary voltage with I2 current.
U1.
Rated supply voltage.
3~ 50/60Hz 50 / 60-Hz three-phase power supply
I
Max
max.
current
1
corresponding current I
U
.
2
I
eff
This is the maximum value of the
1
actual absorbed current considering
the duty cycle. This value usually
corresponds to the capacity of the
fuse (delayed type) to be used as a
protection for the equipment.
IP23S
Protection rating for the housing.
Grade 3 as the second digit means
that this machine may be stored, but
it is not suitable for use outdoors in
the rain, unless it is protected.
Suitable
for
environments.
NOTE: The equipment has also been designed
for use in environments with a pollution
rating of 3. (see IEC 60664).
This equipment complies with a IEC
61000-3-12 standard provided that the
allowed maximum impedance Zmax of
the unit is lower or equal to 0.090 (art.
316 and 317), 0.094 (art. 315) at the
3.300.354
static
frequency
absorbed
at
the
and voltage
2
use
in
high-risk
interface point between the user unit and
the mains.
The fitter or the unit user are responsible
for connecting the unit to a power supply
with
a
maximum
impedance Zmax) lower or equal to
0.090 (art. 316 and 317), 0.094 (art. 315).
4.3
Commands and fittings description
(fig. 4).
A Connector. Connector type DB9 (RS232
serial line) to use for updating the Welding
System programs (Power Source, Wire Feeder
and Control Panel).
B Connector. Connector USB type to use for
updating the Welding System programs
(Power Source, Wire Feeder and Control
Panel).
C Socket. Connect the earth cable connector
(workpiece potential).
D Gas hose fitting. Not used in MIG.
E Connector.
Connect
connector of the Power Source - Wire Feeder
extension (2).
F Socket. Connect the power cable connector of
the Power Source - Wire Feeder extension (2).
G Slide switch. For CANbus-2 line terminating
resistor insertion (default = Off).
H Slide switch. Not used (default = Off).
I CANbus-2 connector. Connect the connector
of the cable (3) to connect the Power Source
to the Robot Interface or Robot Control.
L CANbus-1 connector. Connect the connector
of the cable (1) to connect the Power Source
to the Control Panel.
M Switch. Main switch of the Welding System
(Power Source, Wire Feeder, Control Panel
and Robot Interface) (not including the Robot
management part).
N Power cord.
O Fuse holder. Fuse inserted on Cooling Unit
power supply.
P Cooling Unit socket. Connect the GRV12
Cooling Unit supply cable.
Q Pressure switch socket. Connect the GRV12
Cooling Unit pressure switch cable.
17
allowed
system
GB
the
service
cable
15-04-2013
Publicidad
