VALBERG WM 612 E W205T Instrucciones De Uso página 12

A
Using the appliance
• Shirts
This programme is used to wash cotton, synthetic and blended shirts at the same time. It
removes wrinkles. It involves a pre-treatment.
Apply the chemical pre-treatment product directly to your clothes or add it into the detergent
when the water is put into the main wash compartment. This way, the machine washes your
clothes in a short period of time, which increases the life of your shirts.
• Down jackets
Use this programme to wash down coats, vests, jackets, etc. that are labelled «machine
washable". Thanks to the special spinning parameters, the water reaches the air spaces in
the down.
• Cleaning the drum
For better cleanliness, use this programme regularly (once a month or every two months)
to clean the drum. Run the programme when the machine is completely empty. For best
results, add a washing machine powder descaler to detergent compartment no. 2. At the end
of the programme, leave the door slightly open to dry the inside of the machine.
NOTE:
- This is not a wash programme. This is a maintenance programme.
- Do not run the programme when there is laundry in the machine. Otherwise, it will detect
the load and interrupt the programme.
Special programmes
For specific applications, you can select one of the following programmes.
• Rinse
Use this program when you want to rinse or apply starch without using the wash cycle.
• Spin + Drain
Use this function to spin clothes and drain water from the machine. Before selecting this
programme, select the desired spin speed and press the «Start/Pause» button. Firstly, the
machine will drain the water it contains. Then the machine spins the clothes at the set spin
speed and drains the water that runs out.
If you want to drain the water without spinning your laundry, select the «Spin and pump»
programme and then select the «No spin» function using the spin speed selection button.
Press the Start/Pause button.
NOTE:
Use a low spin speed for delicate fabrics.
22 EN
A
Using the appliance
Speed selection
Each time a new programme is selected, the recommended spin speed of the selected
programme is indicated by the spin speed indicator. To reduce the spin speed, press the spin
speed control button. This speed will decrease gradually. Then, depending on the product
model, the options «Wait for rinse» and «No spin» will appear on the display. When you
select the «No Spin» option, the rinse level indicators will light up.
Delayed rinse
If you do not want to remove your laundry from the machine immediately after the
programme has finished, you can use the "Delayed Rinse» function to keep your laundry
in the final rinse water and prevent your clothes from wrinkling. Press the «Start/Pause»
button after this procedure if you wish to drain the water without spinning. The programme
will resume and stop after draining.
If you want to spin the laundry in water, set the spin speed and press the «Start/Pause»
button.
The programme will restart. The water will be drained, the laundry wrung out, and the
programme is finished.
NOTE:
If the programme has not yet reached the spin stage, you can change the speed
without having to pause the machine.
Delay
With the «Delayed» function, the programme can be started 3, 6 or 9 hours later.
NOTE:
If you intend to use the Delay function, do not use liquid detergent! Your clothes
may be stained.
1. Open the loading door, put your laundry in, put the detergent in the drawer, etc.
2. Select a wash programme and a spin speed.
3. Set the desired time by pressing the «Delay» button. When you press the button once, a
3-hour delay is selected. When you press the same button again, a 6-hour delay is selected
and when you press the same button for the third time, a 9-hour delay is selected. If you
press this button again, the «Delay» function is cancelled.
4. Press the "Start/Pause" button. Over the delay time, the delay indicator light changes
(once every 3 hours).
23 EN