Start Screen - Beretta EXCLUSIVE 25C Manual Para El Instalador Y El Usuario

7

START SCREEN

Upon ignition, the REC10 might:
- request the setting of the TIME & DATE (see paragraph "12.1.1 Time &
date" ).
- display the firmware version and require a button to be pressed in order
to continue.
By pressing the "up" and "down" keys it is possible to move the selection
of the functions in this order:
- PLANT
- STATE
- SET
- INFO
- MENU.
By pressing the "ok" key you access the settings of the selected function
(except for ).
PLANT
The "back" key is inactive (except for
FRI FRI
18/05/2013
MENU
MENU
INFO
INFO
HOT WATER TEMPERATURE
HOT WATER TEMPERATURE
8 PLANT
This item does not represent any specific function.
Instead, it indicates the zone to which the data shown on the start screen
refer, and the zone to which the settings accessible via the other functions
refer.
The presence of one or more zones in addition to PLANT depends
upon the installation's configuration. For this reason, one or more of
the zones cited below may not be present in your configuration, or may
be identified with a different name.
In order to change zones, highlight PLANT if necessary pressing the "up"
and "down" keys.
Then, pressing the "ok" and "back" keys, it will be possible to select the
other zones in this sequence:
- PLANT
- MAIN ZONE
- ZONE 1
- ZONE 2.
The TIME & DATE, LANGUAGE and BACKLIGHT settings are independent
of the selected zone.
The information contained in the INFO menu is independent of the selected
zone.
No domestic hot water parameters can be set if MAIN, ZONE 1 or ZONE
2 is selected.
9 STATE
The function can be used to set the
STATE
operating modes.
To do this, it is necessary to highlight the desired entry using the "up" and
"down" keys and then pressing "ok" to confirm the selection.
Pressing "back" takes you back to the initial screen without making any
selection.
PLANT ).
PLANT
PLANT
12:17
1.3 bar STATE
STATE
42
°C
SET
SET
and
BOILER
STATE
STATE
BOILER
BOILER
MAIN ZONE
MAIN ZONE
9.1 Boiler
This function can be selected in order to set the boiler's status, by choosing
one of the following options:
- OFF
- HOT WATER ONLY
- HEATING AND HOT WATER.
The highlighted status is that which is currently selected. In order to select a
different status highlight it using the "up" and "down" keys and then press
"ok" to confirm the selection. Once the selection has been validated, the
display returns to the
screen without making any selection.
9.1.1 OFF
If OFF is selected, the system shuts off.
The electrical supply and the fuel supply remain active.
9.1.2 Hot water only
If HOT WATER ONLY is selected, the system produces domestic hot water.
Heating is not enabled.
9.1.3 Heating and hot water
If HEATING AND HOT WATER is selected, the system produces domestic
hot water and activates the heating function.
9.2 Main zone
Selecting this function allows you to set the main zone's status, by choosing
one of the following options:
- if the heating programming timing is not enabled:
- ZONE ON
- ZONE OFF
- if the heating programming timing is enabled:
- AUTO
- MANUAL
- HEAT OFF.
MAIN ZONE
In order to select a different status highlight it using the "up" and
"down"keys and confirm the selection by pressing "ok".
Once the selection has been validated, the display returns to the STATE
screen.
Press "back" to return to the STATE screen without making any selection.
9.2.1 ON
If ON is selected, the zone requests are met.
9.2.2 AUTO
If AUTO is selected, the zone requests will be managed based on a
scheduled programme.
screen. Press "back" to return to the start
STATE
BOILER
BOILER
OFF
OFF
HOT WATER ONLY
SUMMER
HEATING AND HOT WATER
WINTER
MAIN
MAIN
ZONE ON
ZONE ON
ZONE OFF
ZONE OFF
MAIN
AUTO
MANUAL
HEAT OFF
ENGLISH
29