Preparations For Use - REMS Ax-Press 25 22 V ACC Instrucciones De Servicio

eng
REMS Power-Ex-Press P-CEF ACC
pipe expander for expanding plastic
Cold Expansions Fittings (P-CEF)
See also www.rems.de → Products → Expanding, Necking →
REMS Power-Ex-Press P-CEF ACC → Catalogue excerpt (PDF)
Operating temperature range
REMS cordless presses
Battery
Rapid charger
Voltage supply
Mains operated presses
Storage temperature range
1.4. Thrust force, stroke
Thrust force (rated force)
REMS Ax-Press 25 22 V ACC
REMS Ax-Press 25 L 22 V ACC
REMS Ax-Press 30 22 V
REMS Ex-Press 22 V ACC
REMS Power-Ex-Press P-CEF ACC
Stroke
REMS Ax-Press 25 22 V ACC,
Ax-Press 25 L 22 V ACC
Ax-Press 30 22 V
REMS Ex-Press 22 V ACC
REMS Power-Ex-Press P-CEF ACC
1.5. Electric Data
REMS Power-Ex-Press P-CEF ACC
REMS Ax-Press 25 22 V ACC /
REMS Ax-Press 25 L 22 V ACC REMS Ax-Press 25 L 22 V ACC
REMS Ax-Press 30 22 V REMS Ax-Press 30 22 V
REMS Ex-Press 22 V ACC
Rapid charger Li-Ion
Rapid charger Li-Ion
Rapid charger Li-Ion
Voltage supply
Voltage supply
1.6. Dimensions
REMS Ax-Press 25 22 V ACC
REMS Ax-Press 25 L 22 V ACC
REMS Ax-Press 30 22 V
REMS Ex-Press 22 V ACC
REMS Power-Ex-Press P-CEF ACC
1.7. Weights
REMS Ax-Press 25 22 V ACC drive unit without battery
REMS Ax-Press 25 L 22 V ACC drive unit without battery
REMS Ax-Press 30 22 V drive unit without battery
REMS Ex-Press 22 V ACC drive unit without battery 22 V 22 V ACC drive unit without battery
without expander
Expander Cu (REMS Ex-Press 22 V ACC)
Expander P (REMS Ex-Press 22 V ACC)
Expander P-CEF (REMS Ex-Press 22 V ACC)
REMS Power-Ex-Press P-CEF ACC drive unit
REMS battery Li-Ion 21.6 V, 1.5 Ah
REMS battery Li-Ion 21.6 V, 2.5 Ah
REMS battery Li-Ion 21.6 V, 5.0 Ah
12
Ø 16 – 63 mm
s ≤ 6,3 mm
–10 °C – +60 °C (14 °F – +140 °F)
–10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +104 °F)
–10 °C – +45 °C (14 °F – +113 °F)
–10 °C – +60 °C (14 °F – +140 °F)
> 0°C (32 °F)
230 V~; 50 – 60 Hz; 450 W
110 V~; 50 – 60 Hz; 450 W
S3 20% (AB 2/10 min)
all-insulated, interference-
suppressed
21.6 V – ---; 1.5 Ah
21.6 V – ---; 2.5 Ah
21.6 V
21.6 V – ---; 5.0 Ah
21.6 V
21.6 V – ---; 9.0 Ah
Input 220 – 240 V~; 50 – 60 Hz; 70 W
Output 21.6 V – ---
all-insulated, interference-suppressed
Input 100 – 120 V~; 50 – 60 Hz; 70 W
Output 21.6 V – ---
all-insulated, interference-suppressed
Input 100 – 240 V~; 50 – 60 Hz; 90 W
Output 21.6 V – ---
all-insulated, interference-suppressed
Input 100 – 240 V~; 50 – 60 Hz; 290 W
Output 21.6 V – ---
all-insulated, interference-suppressed
Input 220 – 240 V~; 50 – 60 Hz
Output 21.6 V – ---; ≤ 15 A – – ---; ≤ 15 A
all-insulated, interference-suppressed
Input 220 – 240 V~; 50 – 60 Hz
Output 21.6 V – ---; 40 A – – ---; 40 A
all-insulated, interference-suppressed
280×260×75 mm (11.0"×10.2"×3.0")
305×260×75 mm (12.0"×10.2"×3.0")
275×290×75 mm (10.8"×11.4"×3.0")
200×250×75 mm (7.9"×9.8"×3.0")
420×245×81 mm (16.5"×9.6"×3.2")
2.6 kg
2.8 kg
4.2 kg
2.0 kg
0.3 kg
0.3 kg
0.3 kg
5.6 kg (12.2 lb)
0.4 kg
0.4 kg
0.8 kg
REMS battery Li-Ion 21.6 V, 9.0 Ah
Pressing heads (pair, average)
REMS expander (average)
Ø ½ – 2" REMS P-CEF expanding head (average)
1.8. Noise information
Emission at workplace
REMS Ax-Press 25 22 V ACC /
L 22 V ACC
REMS Ax-Press 30 22 V
REMS Ex-Press 22 V ACC
REMS Power-Ex-Press P-CEF ACC
1.9. Vibrations
Weighted effective value of acceleration
The specifi ed vibration emission value was measured according to a standard
test method and can be used for comparison with another power tool. The
specifi ed vibration emission value can also be used for an initial estimation of
the cut-out.
CAUTION CAUTION
The vibration emission value may differ from the specifi ed value during actual
use of the power tool depending on the manner in which the power tool is used.
20 kN
Dependent upon the actual conditions of use (periodic duty) it may be necessary
13 kN
to establish safety precautions for the protection of the operator.
30 kN

2. Preparations for Use

20 kN
34 kN
CAUTION CAUTION
After the drive unit has been in storage for a long period of time, the overpres-
sure valve must be actuated fi rst by pressing the reset button (4) before putting
41 mm
back into operation. If it is stuck or stiff, it may not be pressed. The drive unit
23 mm
must be handed over to an authorized REMS customer service workshop for
24 mm
inspection.
44 mm
The respective latest REMS sales literature applies for the use of REMS pres-
sing heads and REMS expanding heads for the different pipe connection
systems, see also www.rems.de → Downloads → Product Catalogues, Brochures.
If the system manufacturer alters components of pipe connection systems or
markets new ones, their current application status must be enquired about at
REMS (Fax +49 7151 17 07 - 110 or e-mail info@rems.de). Subject to change
and error.
2.1. Electrical connection
WARNING WARNING
Note the mains voltage! Before connecting the drive unit, the rapid charger
or the power supply unit, check whether the voltage given on the rating plate
corresponds to the mains voltage. On building sites, in a wet environment,
indoors and outdoors or under similar installation conditions, only operate the
power tool on the mains with a fault current protection switch (FI switch) which
interrupts the power supply as soon as the leakage current to earth exceeds
30 mA for 200 ms.
Rechargeable batteries
Total discharging by undervoltage
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by total discharge. The cells of the REMS Li-Ion
battery are delivered pre-charged to approx. 40 %. Therefore the Li-Ion batteries
must be charged before use and recharged regularly. Failure to observe this
regulation of the cell manufacturer can lead to damage to the Li-Ion battery by
total discharging.
Total discharging due to storage
If a relatively low charged Li-Ion battery is stored, self discharging can lead to
total discharge damage of the battery after longer storage. Li-Ion batteries must
therefore be charged before storing and recharged every six months at the
latest and charged again before use.
NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid
their total discharge. The rechargeable battery will be damaged by total
discharge.
Only use approved REMS rapid chargers for charging the REMS battery, see
Guidelines for use, fi g. 5. New Li-Ion batteries and Li-Ion batteries which have
not been used for a long time only reach full capacity after several charges.
(5.6 lb)
Rapid charger Li-Ion (Art. No. 571575, 571585, 571587)
(6.1 lb)
The left control lamp lights up and remains green when the mains plug is
(9.3 lb)
plugged in. If a battery is inserted in the rapid charger, the green control lamp
fl ashes to indicate that the battery is charging. The green light stops fl ashing
(4,4 lb)
and remains on to signal that the battery is fully charged. If the red control lamp
(0,7 lb)
fl ashes, the battery is defective. If the red control lamp comes on and remains
(0,7 lb)
on, this indicates that the temperature of the rapid charger and / or the battery
(0,7 lb)
is outside the permissible operating range of the rapid charger of 0°C to +40°C.
NOTICE
(0.9 lb)
(0.9 lb)
The rapid chargers are not suitable for outdoor use.
(1.8 lb)
1.1 kg
0.3 kg
0.2 kg
0.2 kg
L = 73 d = 73 d B(A) L L = 84 d L = 84 d B(A) K = 3 dB(A)
pA pA pA WA WA WA WA
L = 74 d = 74 d B(A) L L = 85 d L = 85 d B(A) K = 3 dB(A)
pA pA pA WA WA WA WA
L = 73 d = 73 d B(A) L L L = 84 d = 84 d B(A) K = 3 dB(A)
pA pA pA WA WA WA WA
L = = 81 dB(A) L = 92 dB(A) K = 3 = 92 dB(A) K = 3
pA pA pA WA WA WA
< 2,5 m/s² K = 1,5 m/s²
eng
(2.4 lb)
(0.7 lb)
(0.4 lb)
(0.4 lb)
dB(A)