Tool Use & Setup; Intended Use; Nose Equipment - Stanley PB2500N NeoBolt Manual De Instrucciones

WARNING: To reduce the risk of serious personal injury, disconnect battery pack before making
any adjustments or removing/installing attachments or accessories.
STANLEY Engineered Fastening policy is one of continuous product development and improvement
STANLEY Engineered Fastening policy is one of continuous product development and improvement
and we reserve the right to change the specification of any product without prior notice.
and we reserve the right to change the specifi cation of any product without prior notice.
3. TOOL USE & SETUP
3. TOOL USE & SETUP

3.1 INTENDED USE

3.1 INTENDED USE
The PB2500N tools are designed for installation of STANLEY Engineered Fastening NeoBolt fasteners ONLY.
This tool is a professional power tool. DO NOT let children come into contact with the tool. Supervision is
PB2500N tools are designed for installation of STANLEY Engineered Fastening Neobolt fasteners ONLY.
required when inexperienced operators use this tool. This tool is a professional power tool. Do NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
READ ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE PUTTING TOOL INTO
SERVICE.
READ ALL SAFETY WARNINGS AND INSTRUCTIONS BEFORE PUTTING TOOL INTO
SERVICE.
ALWAYS wear approved hearing and eye protection at all times when using installation
equipment
ALWAYS wear approved hearing and eye protection at all times when using installation
equipment
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
DO NOT use under wet conditions or in presence of flammable liquids or gases.
result.
Electrical Safety
DO NOT use under wet conditions or in presence of flammable liquids or gases.
The electric motor has been designed for one voltage only. Always check that the battery pack voltage
Electrical Safety
corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to
The electric motor has been designed for one voltage only. Always check that the battery pack voltage
that of your mains.
corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds
WARNING: Before adjusting tool, always remove the battery pack.
to that of your mains.
Before use
WARNING: Before adjusting tool, always remove the battery pack.
• Install relevant size nose equipment
• Ensure that the battery is fully charged
Before Use
• Install relevant size nose equipment •
• Insert Battery Pack into the tool
• Ensure that the battery is fully charged
• Quickly pull and release the trigger to set the tool to the home position.
• Insert Battery Pack into the tool
• Quickly pull and release the trigger to set the tool to the home position.

3.2 NOSE EQUIPMENT

3.2 NOSE EQUIPMENT
Removing the anvil (Fig. 1a)
Removing the anvil (Fig. 1a)
• Loosen and remove retaining nut (D) and
• Loosen and remove retaining nut (D) and
remove anvil/nose housing from tool
remove anvil/nose housing from tool
• Using 24mm wrenches, unthread anvil (B) from
• Using 24mm wrenches, unthread anvil (B)
nose housing
from nose housing
• Reverse these steps to install anvil
• Reverse these steps to install anvil
NEW CONTENT BELOW THIS LINE
C
B
D
A
Removing the Collet from tool (Fig. 2)
Removing the Collet from tool (Fig. 2)
• Depress front clutch retaining tabs
• Depress front clutch retaining tabs
• Fully unthread collet from pulling head
• Fully unthread collet from pulling head adapter.
adapter.
• To install collet, depress clutch retaining tabs and
• To install collet, depress clutch retaining tabs
thread collet all the way
and thread collet all the way
NOTE: DO NOT USE WRENCHES TO TIGHTEN COLLET
NOTE: DO NOT USE WRENCHES TO TIGHTEN COLLET
E N G L I S H
E N G L I S H
11
11