Maclaren techno xlr buggy Manual Del Usuario página 4

5 TO FOLD THE BUGGY
Fold the hood back, place the seat to an upright position,
remove contents of the shopping bag, then fasten the
harness.
A Using foot, lift up on footplate to release primary lock until
it pops up.
B Using your foot, press down on the lever sticking out on
the right hand side of the frame.
C Whilst pressing the lever down with your foot, push the
handles forward and inwards.
D Compress folded buggy and engage storage clip.
Use the handle to carefully carry your buggy.
N OTICE: The buggy should always open and fold easily.
Do not force it. It may be necessary to re-read the
instructions.
ASSEMBLY INSTRUCTIONS
6 TO OPERATE THE ADJUSTABLE LEG REST
TO EXTEND THE LEG REST:
Feel through seat corner openings. Locate sliders and loops
and pull forward. Reverse this process to retract leg rest.
7 TO ADJUST SEAT RECLINE
A T O RECLINE SEAT BACK: Position your hand on the seat
recline lever. Gently lift the recline lever with your fingers
whilst taking the weight of the seat back with your hand.
Still maintaining support and holding the lever, gently
recline the seat back in to the desired position. Release
seat recline lever when seat back is in desired position,
ensuring both sides lock at the same time.
B T O RAISE SEAT BACK: From rear of buggy push seat
back to original upright or desired intermediate position.
8 TO ATTACH THE HOOD
A With buggy open clip the hood to the handle tubes just
above the retaining blocks.
B Wrap adjustable straps around handle tubes.
C Place rear apron behind seat back.
D Extend hood and press down on side hinges to lock open.
TO TILT HOOD:
E Fully unzip back panel.
F Tilt hood forward.
G The hood is removed by firmly pressing down the clip
release tabs.
4
C
B
A
B
A
A
D
B
C
G
F
E
9 REMOVING AND REFITTING THE SEAT COVER
Remove hood from buggy if fitted.
Using foot, lift the break pedal, then press down on the lever
sticking out on the right side of the frame.
A Twist shoulder strap end buckles and feed through holes.
B The waist harness back strap is fixed to the chassis behind
the seat. To remove, twist the buckles on each end of the
harness back strap and unthread from the 'D' rings attached
to the chassis.
NOTICE: It is important that the strap be rethreaded through
the 'D' rings after the seat has been refitted. Failure to do so
will endanger your child.
C Feed crotch strap buckle through holes.
D Unclip seat cover retaining straps.
E Unfasten seat fabric from handle tubes and seat base.
F Slide fabric from seat back and base.
G When refitting seat fabric, insert seat back support tubes
into fabric flap.
H When refitting shoulder straps choose the fabric holes
appropriate to the child's size. Twist the buckles and feed
through seat cover, seat back and then through holes in
plastic seat back arms.
J When refitting seat fabric to seat base pass crotch strap
buckle through the hole in the seat fabric and then hole
in seat base.
N OTICE: The seat fabric must be wrapped over the top of the
handle tube and fastened by the button hole.
After assembly pull the seat fabric forward and backward to
ensure it will not come off.
10 TO RE-FIT THE SHOPPING BASKET
A Place bag on the 'X' frame under seat with
lowest edge of bag at front.
B Attach front straps to front legs just below seat.
C Attach rear straps to rear legs just above
horizontal tie bar.
11 TO FIT THE RAIN COVER
A Return hood to non-tilted position before fitting
rain cover.
B Ensure visor is folded away beneath the hood.
C Place the apron over the hood front.
D Attach two eyelets (one each side) to the
hood clips.
E Attach the two eyelets (one each side) to the
front legs.
12 TO ADJUST HANDLE LENGTHS
A Press triggers.
B Slide handles until triggers locate in one of
3 positions. Release triggers to lock.
A
A
B
C
F
E
D
E
G
G
H
J
K
C
B
A
C
D
B
D
A
E
E
B
A
en
F
5