Publicidad
Idiomas disponibles
Idiomas disponibles
j) Disconnect the saw from power supply when performing maintenance
tasks.
k) If the power cord gets damaged during operation, disconnect the
power supply immediately. DO NOT TOUCH POWER CORD BEFORE
DISCONNECTING FROM THE POWER SUPPLY.
l) If the saw is equipped with laser, replacement with laser of another type
is forbidden and all repairs must be carried out by the service. Do not
aim the laser beam at people or animals.
m) Do not use the tool in stationary mode. It is not designed for use with
sawing table.
n) Fix processed material to stable surface and secure with clamps or vice
to eliminate shifting. This kind of work piece fixation is safer than
holding the work piece in hand.
o) Wait until blade comes to a complete stop before putting the power
tool away. Cutting blade may jam and cause loss of control over the
power tool.
SAFETY RULES FOR LASER DEVICE
Laser device used in the saw design is the class 2 with maximum
power below 1 mW and wavelength λ = 650 nm. Such device is not
dangerous to eyes, however do not look directly at the source of the
light (temporary blindness hazard).
WARNING. Do not look directly at the source of the laser beam.
It may cause hazards. Follow the below safety rules.
Use the laser device in accordance with the manufacturer's
instructions.
Do not, either intentionally or unintentionally, point the laser beam at
people, animals or any object other than processed material.
Do not bring to accidental pointing the laser beam at bystanders' or
animals' eyes for a period longer than 0.25 second, for instance by
pointing the laser beam at mirrors.
Always ensure the laser beam is directed at material which does not
have any reflective surfaces.
Reflective steel sheet (and other materials with reflective surface) does
not allow for laser use, because it might cause hazardous light reflection
directed at operator, bystanders or animals.
Do not replace the laser unit with device of other type. All repairs must
be carried out by the manufacturer or authorized person.
Caution: Laser radiation.
CAUTION: Adjustments other than described in this manual put
in danger of exposition to laser radiation!
CAUTION! This device is designed to operate indoors. The design is
assumed to be safe, protection measures and additional safety
systems are used, nevertheless there is always a small risk of
injuries at work.
Explanation of used symbols.
LASER LIGHT, LASER RADIATION DO NOT LOOK
AT THE LASER BEAM LASER DEVICE CLASS 2
Wavelength: 650 nm; Output: < 1 mW EN
60825-1:2014
1. Note! Take special precautions!
2. Read the operating manual, observe the warnings and safety
conditions contained in it!
3. Use personal protective equipment (safety goggles, hearing
protection, dust mask).
4. Use protective gloves.
5. Keep children away from the tool.
6. Use protective clothing.
7. Protect the device against moisture.
8. Remove the battery from the device before performing any
adjustments or cleaning operations
9. Note! Laser radiation!
10. Note! Sharp elements!
CONSTRUCTION AND USE
Circular saw is a battery-powered tool. Drive consists of a DC
commutator motor with permanent magnets and gear. Power tools of
this type are widely used for cutting wood and wood- based materials.
Do not use the saw for cutting firewood. Attempts to use the saw for
purposes other than specified will be considered an improper use. Use
the circular saw only with appropriate cutting blades with teeth with
sintered carbide tips. Circular saw is designed for light duty works in
service workshops and any individual, amateur activities (tinkering).
WARNING! Use the power tool according to the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1.
Dust extraction outlet
2.
Upper guard
3.
Switch lock button
4.
Switch
5.
Lower guard lever
6.
Front handle
7.
Lighting
8.
Cutting blade
9.
Flange washer
10.
Fixing bolt for cutting blade
11.
Lower guard
12.
Cutting depth guide
13.
Main handle
14.
Battery installation socket
15.
Spindle lock button
16.
Footplate
17.
Knob for base bevel adjustment
18.
Cutting line indicator for 45°
19.
Cutting line indicator for 0°
20.
Edge guide locking screw
21.
Cutting depth locking knob
22.
Edge guide
* Differences may appear between the product and drawing.
EQUIPMENT AND ACCESSORIES
1. Edge guide- 1 pce
2. Hexagonal key - 1 pce
12
Publicidad
