Descargar Imprimir esta página

GRAPHITE 59G812 Manual De Usuario página 14

Ocultar thumbs Ver también para 59G812:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 89
The screw securing the cutting disc has a left-hand thread.
Special care must be taken when gripping the cutting disc. You
must use protective gloves to ensure that your hands are
protected from contact with the sharp teeth of the cutting disc.
REPLACEMENT OF BATTERIES IN THE LASER MODULE
The laser module is powered by two 1.5 V AAA batteries.
• Open the battery tray cover (36) (Fig. F).
• Dispose of used batteries.
• Insert new batteries, making sure that the correct polarity is
observed.
• Fit the battery tray cover.
REPLACEMENT OF CARBON BRUSHES
Worn (shorter than 5 mm), burnt or cracked carbon brushes of the motor
must be replaced immediately. Always replace both brushes at the same
time.
• Unscrew the carbon brush covers (8).
• Remove used brushes.
• Remove any carbon dust, if any, using compressed air.
• Insert new carbon brushes (brushes should slide freely into
brushstops).
• Fit the carbon brush covers (8).
After replacing the carbon brushes, start the power tool without
a load and wait 1-2 minutes until the carbon brushes fit into the
motor commutator. Only a qualified person should replace the
carbon brushes using original parts.
Any defects should be rectified by the manufacturer's authorised
service department.
TECHNICAL SPECIFICATIONS
RATING DATA
Mitre saw 59G812
Parameter
Supply voltage
Rated power
Disc speed (no load)
Type of work
Guide length
Angle cutting range
Diagonal cutting range
Maximum depth of cut
Outer diameter of the cutting disc
Inner diameter of the cutting disc
Dimensions of the material
to be cut under
angled / angled
Laser class
Laser power
Laser light wavelength
Protection class
IP degree of protection
Mass
Year of production
59G812 indicates both the type and the designation of the
machine
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Vibration acceleration values
Information on noise and vibration
The noise emission level of the equipment is described by: the
emitted sound pressure level Lp
Value
230V AC 50Hz
1800 W
-1
4800 min
S6 25%
195 mm
± 45°
0° ÷ 45°
75 mm
254 mm
30 mm
0° x 0°
90 x 280mm
45° x
90 x 200mm
45° x
50 x 200mm
45°
0° x
50 x 280mm
45°
II
< 1mW
λ = 650 nm
II
IPX0
15.72 kg
Lp
=95.2 dB(A) K=
A
3 dB(A)
Lw
=108.2 dB(A)
A
K= 3 dB(A)
= 2.936 m/s²
a
h
2
K=1.5 m/s
and the sound power level Lw
A
(where K denotes measurement uncertainty). The vibrations
emitted by the equipment are described by the vibration
acceleration value a
h
The sound pressure emission level Lp
and the vibration acceleration value a
have been measured in accordance with EN 62841-1:2015. The
vibration level a
given can be used to compare equipment and to
h
make a preliminary assessment of vibration exposure.
The vibration level quoted is only representative of the basic use of
the unit. If the unit is used for other applications or with other work
tools, the vibration level may change. Higher vibration levels will be
influenced by insufficient or too infrequent maintenance of the unit.
The reasons given above may result in increased vibration
exposure during the entire working period.
In order to accurately estimate vibration exposure, it is
necessary to take into account periods when the unit is
switched off or when it is switched on but not used for work.
Once all factors have been accurately estimated, the total
vibration exposure may turn out to be much lower.
In order to protect the user from the effects of vibration, additional
safety measures should be implemented, such as cyclical
maintenance of the machine and working tools, securing an
adequate hand temperature and proper work organisation.
ENVIRONMENTAL PROTECTION
Electrically-powered products should not be disposed of with
household waste, but should be taken to appropriate facilities
for disposal. Contact your product dealer or local authority for
information on disposal. Waste electrical and electronic
equipment contains substances that are not environmentally
friendly. Unrecycled equipment poses a potential risk to the
environment and human health.
* Subject to change.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with
its registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: "Grupa Topex")
informs that all copyrights to the content of this manual (hereinafter: "Manual"),
including, among others. Its text, photographs, diagrams, drawings, as well as its
composition, belong exclusively to Grupa Topex and are subject to legal protection
under the Act of 4 February 1994 on Copyright and Related Rights (ie Journal of Laws
2006 No. 90 Poz. 631, as amended). Copying, processing, publishing, modification
for commercial purposes of the entire Manual and its individual elements, without the
consent of Grupa Topex expressed in writing, is strictly prohibited and may result in
civil and criminal liability.
EC Declaration of Conformity
Manufacturer: Grupa Topex Sp. z o.o. Sp.k., Pograniczna 2/4 02-
285 Warszawa
Product: Mitre saw
Model: 59G812
Trade name: GRAPHITE
Serial number: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility
of the manufacturer.
The product described above complies with the following documents:
Machinery Directive 2006/42/EC
Electromagnetic Compatibility Directive 2014/30/EU
RoHS
Directive
2011/65/EU
2015/863/EU
And meets the requirements of the standards:
EN 62841-1:2015; EN 62841-3-9:2015/A11:2017;
EN 55014-1:2017; EN 55014-2:2015; EN IEC 61000-3-2:2019; EN
61000-3-11:2000;
EN IEC 63000:2018
Notified body:
No. 0123; TŰV SŰD Product Service GmbH, Ridlerstraβe 65,
80339 Műnchen, Germany
EC type-examination certificate no:
M8A 044390 1135 Rev. 01
This declaration relates only to the machinery as placed on the
market and does not include components
added by the end user or carried out by him/her subsequently.
Name and address of the EU resident person authorised to prepare
the technical dossier:
Signed on behalf of:
Grupa Topex Sp. z o.o. Sp.k.
2/4 Pograniczna Street
02-285 Warsaw
A
13
(where K is the measurement uncertainty).
, the sound power level Lw
A
given in these instructions
h
as
amended
A
by
Directive

Publicidad

loading