Operation And Maintenance; Technical Parameters - GRAPHITE 58G023 Manual Del Usuario

cut off.
If the object is small, fix the processed material with F-clamps. If the circular
saw base does not move on the processed material, but is lifted instead, there
is danger of kick back.
Properly fixed processed material and firm hold of the tool ensure full control
over power tool operation. This allows to avoid risk of body injury. Do not try
to hold short pieces of material with your hand.
SAW BASE ADJUSTMENT FOR BEVEL CUTTING
Adjustable saw base allows making bevel cuts at angles ranging from 0° to 45°.
• Loosen the base position locking lever (17) (fig. J).
• Use the scale to set the base (16) at desired angle (from 00 to 450).
• Lock the base position locking lever (17).
Remember that for bevel cutting the risk of kick back is greater (pinching of
cutting blade more probable), therefore it is particularly important that the
saw base rests on the processed material with its whole surface. Perform
cutting with smooth move.
MAKING A CUT BY PLUNGING INTO MATERIAL
• Set desired cutting depth that matches thickness of material planned to be cut.
• Tilt the saw so the front edge of the base (16) rests on the cut material and
0° marker for perpendicular cutting is in the line of planned cutting.
• When the saw is in the place to start cutting, lift the lower guard (11) with
the lower guard lever (5) (cutting blade is lifted above the material).
• Switch the power tool on and wait until cutting blade reaches its full
rotational speed.
• Gradually lower the saw and plunge the cutting blade in material (front
edge of the saw base should stay in contact with surface of the material
during this move).
• When the blade starts cutting, release the lower guard.
• When whole surface of the saw base rests on the material, move the saw
forward to proceed with cutting.
• Never move the saw backwards when the blade is rotating, there is danger
of kick back.
• Finish cutting in reverse order it was started, by turning the saw around line
of contact of the processed material and the front edge of the tool base.
• Before removing blade from the material, allow it to stop after switching
the saw off.
• Finish the corner fillets with reciprocating saw or hand saw when necessary.
CUTTING OR CUTTING OFF LARGE PIECES OF MATERIAL
When cutting large planks or boards of material support them well to avoid
potential blade hitch (kick back) due to pinching the blade in material kerf.

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing any
activities related to installation, adjustment, repair or maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a brush or blow through with compressed air at low pressure.
• Do not use any cleaning agents or solvents, since they may damage plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent device
overheating. Do not clean ventilation holes by inserting sharp objects
there, such as screwdrivers and other similar objects.
• During normal operation cutting blade gets blunt after some time. When
it happens it is necessary to apply greater pressure when moving the saw
during cutting.
• When cutting blade is found damaged, replace it immediately.
• Cutting blade must always be sharp.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
CUTTING BLADE REPLACEMENT
• Use supplied hexagonal key to unscrew the fixing bolt for cutting blade (10)
by turning it counter-clockwise.
• To prevent rotation of the saw spindle, lock the spindle with spindle lock
button (12) when unscrewing the bolt that fixes the cutting blade (fig. K).
• Disassemble the outer flange washer (9).
• Use the lower guard lever (5) to move the lower guard (11) so it is hidden in
the upper guard (2) maximally (check condition and operation of the spring
that pulls the lower guard at that time).
• Slide the cutting blade (8) out through the slit in the saw base (16).
• Position new cutting blade so blade teeth and arrow on the blade match
direction of the arrow on the lower guard and upper guard.
• Slide the cutting blade into base slot and install on the spindle so it is well
pressed against surface of the inner flange and centred when seated on
its neck.
• Install outer flange washer (9) and tighten the fixing bolt for cutting blade
(10) by turning it clockwise.
• Always put the hexagonal key in its storage place after replacement of
cutting blade.
When installing cutting blade, observe correct direction of the teeth. Arrow
on the saw body shows direction of spindle rotation.
Be very careful when holding the cutting blade in hand. Use protective gloves
to provide protection for your hands against sharp teeth of cutting blade.
All defects should be repaired by service workshop authorized by the
manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless Circular Saw 58G023
Parameter
Battery voltage
Rotational speed (no load)
Bevel cutting range
Outer diameter of cutting blade
Inner diameter of cutting blade
Cutting thickness at right angle
Cutting thickness at 45°
Laser class
Laser power
Wavelength
Protection class
Weight
Year of production
58G023 defines type and indication of the device
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration (additional handle)
Vibration acceleration (main handle)
Noise and vibration information
14
Value
18 V DC
0-4200 rpm
0° ÷ 45°
165 mm
20 mm
52 mm
35 mm
2
< 1mW
λ = 650nm
III
2.95 kg
2020
Value
58G001 58G004
18 V DC 18 V DC
Li-Ion Li-Ion
2000 mAh 4000 mAh
4 C – 40 C 4 C – 40 C
0 0 0 0
1 h 2 h
0,400 kg 0,650 kg
2020 2020
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 C – 40 C
0 0
1 h
2 h
II
0,300 kg
2020
Lp = 75,86 dB (A) K=3dB (A)
A
LW = 86,3 dB (A) K=3dB (A)
A
a = 3,92 m/s K=1,5 m/s
2 2
h
a = 2,18 m/s K=1,5 m/s
2 2
h