Operation And Maintenance; Technical Parameters; Environmental Protection - GRAPHITE 58G067 Manual Del Usuario

CUTTING A HOLE IN MATERIAL
• Make a hole in processed material with 10 mm diameter.
• Put blade into the hole and start cutting from that spot.
METAL CUTTING / TYPES OF BLADES
Use appropriate blades with more teeth for cutting of metal.
For metal cutting use appropriate lubricant (e.g. cutting oil). Metal
cutting without lubrication leads to rapid wear of blade. The below
table gives the best choices for blade type:
Teeth per
Blade length
inch
24
14 80 mm
9
• Use only appropriate and sharp blades.
• Do not use blades with damaged shank.
• Use appropriate blade types.

OPERATION AND MAINTENANCE

Unplug the power cord from mains socket before commencing
any activities related to installation, adjustment, repair or
maintenance.
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the device with a dry cloth or blow through with
compressed air at low pressure.
• Do not use any cleaning agents or solvents, since they may
damage plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• Regular lubrication of guiding roller is recommended. A drop of oil
applied in this spot will prolong lifetime of the roller.
• In case of power cord damage replace it with a cord with the same
specification. Entrust the repair to a qualified specialist or return
the tool to a service point.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
• always store the tool in a dry place, beyond reach of children.
REPLACEMENT OF CARBON BRUSHES
Immediately replace worn out (shorter than 5 mm), burnt or
cracked motor carbon brushes. always replace both carbon
brushes at a time.
Entrust replacement of carbon brushes only to a qualified person.
Use only original parts.
All defects should be repaired by service workshop authorized by
the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Jigsaw 58G067
Parameter
Supply voltage
Power supply frequency
Rated power
Blade stroke cycles (without load)
M a x i m u m Wood
thickness of
Metal
cut material
Application range
Soft steel, non-ferrous metals
Non-ferrous metals, plastics
Wood, plywood
Value
230 V AC
50 Hz
650 W
0-3100 min -1
65 mm
8 mm
Blade stroke length
Protection class
Weight
Year of production
58G067 defines type and indication of the device
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration (cutting
a plate)
Vibration acceleration (cutting
a metal sheet)
Noise and vibration information
Noise produced by the device is defined with: level of produced
sound pressure Lp and level of sound power Lw
A
measurement uncertainty). Vibrations produced by the device
are defined with vibration acceleration value a
measurement uncertainty).
Sound pressure Lp , sound power Lw
A
specified in this manual have been measured in accordance with EN
62841-1:2015. Specified vibration level a
tools and for initial evaluation of exposition to vibrations.
Specified vibration level is representative only for main applications
of the device. When the device is used for other purposes or with
different working tools, the vibration level may change. Insufficient
or too rare maintenance may increase vibration level. The
abovementioned factors may lead to higher exposure to vibrations
during whole working time.
In order to precisely define exposure to vibrations, include
periods when the device is switched off and when it is switched
on but not used for working. Once all factors have been carefully
considered, total exposition to vibrations may be significantly
lower.
To protect the user from results of exposure to vibrations, use
additional safety measures such as: device and working tool periodic
maintenance, proper hand temperature conditions, good work
organisation.

ENVIRONMENTAL PROTECTION

Electrical equipment must not be disposed off with household
waste and, instead, should be utilized at appropriate facilities.
Information on utilization can be provided by the product
vendor or the local authorities. Waste electrical and electronic
equipment contains substances that are not neutral to
the natural environment. Equipment that is not recycled
constitutes a potential hazard to the environment and to
human health.
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with seat in
Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs, that all copyrights to this
instruction (hereinafter Instruction), including, but not limited to, text, photographies, schemes,
drawings and layout of the instruction, belong to Grupa Topex exclusively and are protected
by laws accordingly to Copyright and Related Rights Act of 4 February 2004 (ustawa o prawie
autorskim i prawach pokrewnych, Dz. U. 2006 No 90 item 631 with later ammendments). Copying,
processing, publishing, modifications for commercial purposes of the entire Instruction or its
parts without written permission of Grupa Topex are strictly forbidden and may cause civil and
legal liability.
13
18 mm
II
2,1 kg
2019
Lp = 84,6 dB(A) K= 3 dB(A)
A
Lw = 95,6 dB(A) K= 3 dB(A)
A
a = 4,535 m/s² K= 1,5 m/s²
h
a = 4,008 m/s² K= 1,5 m/s²
h
(where K is
A
(where K is
h
and vibration acceleration a
A h
can be used to compare
h