Publicidad
Idiomas disponibles
Idiomas disponibles
GB
MT
Laser power .......................................................... < 1 mW
Laser module power supply .................. 2 x 1.5 V Micro (AAA
) ..........................97 dB(A); K
Sound pressure level (L
pA
Sound power level (L
)
WA
measured .......................................... 110 dB(A); K
* Operating mode S6 40%: Continuous operation with intermittent load
(cycle time 10 min). In order not to heat the motor more than permitted,
the motor may only be operated for 40% of the cycle time with the stated
nominal power and must then continue running for 60% of the cycle time
without a load.
**Operating mode S1: Continuous operation with constant load
This appliance is intended to be operated using a mains supply
network with a system impedance (internal resistance of the
mains) Zmax on the transfer point (house connection) of maximum
0.369 Ohm. The user must ensure that the appliance is only op-
erated using a mains supply network meeting the requirements. If
necessary, local power supply companies can be consulted with
regards to the system impedance.
-
The specifi ed total vibration value and the stated noise emis-
sion value have been measured according to a standardised
test method and can be used to compare one power tool with
another.
-
The specifi ed total vibration value and the stated specifi ed
noise emission value can also be used for a provisional as-
sessment of the load.
Warning:
The vibration and noise emissions may deviate from the
specifi ed values during actual use of the power tool,
depending on how the power tool is being used and, in
particular, what kind of material is being worked on.
Safety measures for the protection of the operator are to
be determined that are based on an estimate of the actual
vibration load under the real operating conditions (for
this, all parts of the operating cycle are to be taken into
account, for example, times in which the electric tool is
turned off, and those during which it is turned on but run-
ning without a load).
Safety instructions
CAUTION! The following basic safety precautions must be ob-
served while using electric tools to protect against electric shock,
injury and risk of fi re. Please read all instructions before using this
electric tool and keep the safety instructions in a safe place.
Symbols and icons
Symbols on the appliance:
Carefully read these Operating Instructions.
Wear eye protection.
Wear ear protection.
Wear breathing protection.
Caution - Risk of injury.
Never reach into the running blade.
Do not expose the unit to rain. The device must not be
wet, nor should it be operated in a moist environment.
36
Caution! - Laser radiation. Do not look into the beam.
Laser class 2
= 3 dB
pA
= 3 dB
WA
This label is attached to the saw blade guard.
Safety class II (Double Isolated)
Electrical appliances must not be disposed of with the
domestic waste.
Speed 3200 min
3200RPM
Speed 5000 min
5000RPM
254mm
Max. diameter, saw blade: ø 254 mm
The saw blade should be wider than 2.5 mm at the
>2.5mm
saw teeth
The saw blade should be no thicker than 1.9 mm
<1.9mm
The riving knife is 2.5 mm thick
t=2.5mm
Graphical symbol additionally on the saw blades
Caution - a damaged blade must not be used under any
circumstances. Replace the saw blade immediately.
Symbols in the manual
Warning symbols with information on damage
and injury prevention.
Instruction symbols with information on preventing dam-
age.
Help symbols with information on improving tool
handling.
Hazard symbol with information on the prevention of per-
sonal injury caused by electric shock.
Warning! Electric shock hazard.
Always unplug the device before working on it.
General safety instructions for power tools
WARNING! Read all safety directions and in-
structions. Omissions in the compliance with safety
directions and instructions can cause electrical shock, fi re
and/or severe injuries.
Retain all safety directions and instructions for
future use.
The term "Power Tools" used in the safety instructions refers to
mains-operated power tools (with power cord) and to battery-
operated power tools (without power cord).
-1
-1
Specifi ed rotation direction of the saw blade
Publicidad
