Descargar Imprimir esta página

GGP ITALY SBC 627 K Manual De Instrucciones página 115

Desbrozadora de motor portátil manualmente

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 125
tive gloves to handle the cutting devices.
Mount the components very carefully so as
not to impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
WARNING!
  Unpacking  and  completing 
the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always mak-
ing use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
1.1 COMPLETING THE MACHINE
1.1a. Models SBC 627 K – 635 K – 645 K
653 K (Fig. 1)
– Slide the contoured plate (1) until it is close to
the holes in the drive tube (2).
– Fit the top part (3) of the front handgrip on the
plate (1) so that the pin (4) fits into one of the
three holes provided on the drive tube (2) to
adjust the handgrip to the operator's prefer-
ence.
– Join the bottom part (5) with the guard and at-
tach it to the top part (3), tightening the screw
(6) completely.
1.1b Models SBC 627 KD – 635 KD – 643 KD
(Fig. 2)
– Unscrew the middle knob (1) and remove the
cap (2).
– Insert the handle bar (3), making sure that the
controls are on the right.
– Set the handle bar in the most comfortable
working position and lock it using the cap (2)
and knob (1).
– Fasten the casing (4) of the controls to its ca-
ble fastener (5).
NOTE Loosening the knob (1) the handle bar can
be rotated to reduce its bulk for storage.
1.1c Models SBC 645 KD – 653 KD (Fig. 3)
– Lift the lever (1) and remove it loosening the
screw (2).
– Remove the cap (3) from the support (4).
– Put the handle bar (5) into the seat in the sup-
port (4), making sure that the controls are on
the right.
– Fit the cap (3) and lever (1), without tightening
the screw (2).
– Lower the lever (1) and check that the handle
bar (5) is firmly locked; if not, tighten the screw
(2) until it is satisfactorily locked.
– Fasten the casing (6) of the controls to its ca-
ble fastener (7).
NOTE Lifting the lever (1) the handle bar can be
moved to the position most comfortable for the
operator.
1.1d Models SBC 645 KF – 653 KF (Fig. 4)
– Slide the contoured plate (1) until it is close to
the holes in the drive tube (2).
– Fit the top part (3) of the front handgrip on the
plate (1) so that the pin (4) fits into one of the
three holes provided on the drive tube (2) to
adjust the handgrip to the operator's prefer-
ence.
– Join the bottom part (5) with the guard and at-
tach it to the top part (3), tightening the screw
(6) completely.
– Remove the protective cuffs (11) from both
ends of the flexible drive tube (12), taking note
that there are differences between them.
– Lift the pin (13), turning it so that it remains
lifted and insert the end with the hole (12a) in
the seat of the power unit, ensuring that the
hole is turned upward.
– Release the pin (13), making sure it is lowered
completely to lock the end of the tube (12a).
– Insert the end with the groove (12b) in the
protruding hub of the front handgrip (14) and
fasten it with the screw (15) ensuring it stays
locked.
– Insert the register (17) of the throttle wire in
the support slot and connect the wire (18) to
the carburettor lever (19); then work the nuts
(20) to tighten the wire and block the register
on the support.
– Connect the two terminals of the cables (21)
and (22) to the corresponding cables on the
power unit.
1.2 FITTING THE GUARD ON THE CUTTING
DEVICE (Fig. 5)
WARNING!
Each cutting device is pro-
vided with a specific guard. Never use guards
other than those indicated for each cutting
device.
WARNING!
Wear protective gloves and
fit the blade guard.
– Remove the screw (1) from the guard (2).
– Insert the tab (3) in the guard seat (2) and fas-
ten the guard with the screw (1).
1.3 FITTING AND REMOVING CUTTING
DEVICES AND PREPARING GUARDS
WARNING!
5
Use
only
original
cut-

Publicidad

loading