GGP ITALY SBC 627 K Manual De Instrucciones página 116

ting devices or ones homologated by the
Manufacturer.
1.3.1 Selecting the cutting device
Choose the most suitable cutting device for the
job to be done, according to these general indi-
cations:
– the 3-point blade is suitable for cutting brush-
wood and small shrubs up to 2 cm in diameter;
– the 4-point blade is suitable for cutting tough
grass over large surfaces;
– the cutting line head can eliminate tall grass
and non-woody vegetation near fences, walls,
foundations, pavements, around trees, etc. or
completely clean a particular area of the gar-
den;
– the saw blade (if permitted) allows small
woody parts to be cut and small trees to be
felled.
Every cutting device must be fitted with a specif-
ic guard, as indicated by the following directions.
IMPORTANT The cutting devices are fastened
with a left-hand thread and therefore must be un-
screwed clockwise and screwed on anticlock-
wise. Remove all elements that may have been
assembled, which will be used in various con-
figurations, according to the cutting device used.
1.3.2 3 or 4-point blade "Tri-Arc" blade"
(Fig. 6)
a) Assembly
– Fit the inner ring-nut (1) in the indicated di-
rection, making sure that the inner ring-nut's
grooves match perfectly with those of the an-
gle transmission (2).
– Fit the blade (3) and the outer ring-nut (4), with
the flat part toward the blade.
– Insert the supplied wrench (5) in the specific
hole, then turn the blade (3) by hand and push
the wrench (5) until it enters the hole of the an-
gle transmission (2), blocking rotation.
– Fit the cup (6) fully tightening the nut (7) anti-
clockwise (25 Nm).
– Remove the wrench (5) to restore rotation.
b) Adjusting the guard
– Remove the additional guard (8 - if already fit-
ted), unhooking hooks clicked into the guard
(9).
c) Disassembly
– Insert the supplied wrench (5) in the specific
hole, then turn the blade (3) by hand and push
the wrench (5) until it enters the hole of the an-
gle transmission (2), blocking rotation.
– Unscrew the nut (7) clockwise and remove
the cup (6).
– Pull out the outer ring-nut (4), then remove the
blade (3) and the inner ring-nut.
1.3.3 Cutting line head (Fig. 7)
a) Assembly
– Fit the inner ring-nut (1) in the indicated di-
rection, making sure that the inner ring-nut's
grooves match perfectly with those of the an-
gle transmission (2).
– Insert the supplied wrench (3) in the specif-
ic hole of the inner ring-nut (1), then turn the
ring-nut by hand and push the wrench (3) until
it enters the hole of the angle transmission (2),
blocking rotation.
– Fit the cutting line head (4) screwing it anti-
clockwise.
– Remove the wrench (3) to restore rotation.
b) Adjusting the guard
– Fit the additional guard (8), inserting the cou-
plers into the respective seats in the guard (9)
and pressing until a click is heard.
WARNING! When using the cutting line
head, the additional guard, with line cutting
knife, must always be fitted.
c) Disassembly
- Insert the supplied wrench (3) in the specific
hole of the inner ring-nut, then turn the ring-nut
by hand and push the wrench (3) until it enters
the hole of the angle transmission (2), block-
ing rotation.
– Remove the cutting line head (4) unscrewing
it clockwise.
1.3.4 Saw blade (if permitted) (Fig. 8)
a) Assembly
– Fit the inner ring-nut (1) in the indicated direc-
tion, making sure that the grooves match per-
fectly with those of the angle transmission (2).
– Fit the blade (3) and the outer ring-nut (4), with
the flat part toward the blade.
– Insert the supplied wrench (5) in the specific
hole, then turn the blade (3) by hand and push
the wrench (5) until it enters the hole of the an-
gle transmission (2), blocking rotation.
– Fit the cup (6) fully tightening the nut (7) anti-
clockwise (25 Nm).
– Remove the wrench (5) to restore rotation.
b) Adjusting the guard
– Remove the guards that may have been used
6