Jacuzzi J-460 Manual De Instalación página 33

I
The use of alcohol, narcotics or medicines may cause drowsi-
ness, and affect pulse rate, blood pressure and circulation. Avoid
using these substances before getting into the spa.
I
Do not use a spa immediately following strenuous exercise.
Electrical safety
®
The MaxiJacuzzi are safe products, manufactured in com-
pliance with standards 60335-1: 2002, 60335-2-60: 2003,
60825-1: 1994+A1+A2, EN 55014-2, CISPR 22 CLASS B,
EN 61000-3-2, EN 6100-3-3
ensure user safety.
I
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with
proper installation procedures.
It is the responsibility of the installer to select mate-
rials based on their intended use, to carry out work
properly, to check the condition of the system that
the unit will be connected to and that it ensures
safety of use also concerning maintenance work
and the possibility to examine the system.
I ®
The MaxiJacuzzi are class "I" appliances and therefore
they must be permanently connected, without any inter-
mediate connections, to the electrical system and to the
protection system (earth system).
The electrical system of the building must be
provided with a 0.03A differential switch and
with an efficient protection (earth) circuit. Check
for proper operation of the differential switch by
pressing the TEST button, which should trip.
I
For connection to the electrical mains, it is necessary to
install an omnipolar cut-off switch as per the values indi-
cated in the chapter "Electrical characteristics., which is to
be located in an area which is compliant with safety instruc-
tions and which cannot be reached by the users who are
®
using the MaxiJacuzzi .
It is mandatory to comply with this instruction. Any other pro-
cedure is prohibited.
I
The installation of electrical devices and equipment (sock-
ets, switches, etc.) near the MaxiJacuzzi
ance with legal standards and regulations in the country
®
where the MaxiJacuzzi
I
The omnipolar switches which were previously mentioned
must ensure an opening of contacts of at least 3 mm, and
they must be compliant with the voltage and current as spec-
ified in the chapter "Technical characteristics".
I
For the equipotential connection as required by specific
national standards, the installer must use the terminal pro-
vided (standard EN 60335.2.60) in the electrical box, and
and tested during production to
®
must be in compli-
is installed.
marked with the symbol
condition must be established for all metallic masses sur-
rounding the spa, for example water and gas pipes, metallic
platforms, and so on.
Refer to the pre-installation information sheet for
instructions and electrical input of the various models.
Start-Up Instructions
Read each step in its entirety before proceeding with
that step.
I
Remove any dirt from the spa. Although the spa shell has
been polished at the factory, you may want to treat it with a spe-
cially formulated spa cleaner and wax available from your dealer
prior to filling the first time.
I
Filling the Spa
Remove the filter cover, then remove both filter cartridges as out-
lined in section "Cleaning The Filters".
Place the end of your garden hose into empty skimming filter bucket
(filter bucket on your left) as you stand next to the spa. Fill spa half
way, then place the garden hose into the opposite filter bucket (fil-
ter bucket on your right) while adding the remaining fill water.
Fill spa until water level is above all jets and just touching the
bottom of each headrest in its lowest position.
Do not overfill your mini-pool.
N.B.: If your water is extremely hard, it is preferable to fill
halfway with hard water and the rest of the way with softened
water. Or, you may fill entirely with hard water if you use a spe-
cial water additive.
Always fill the spa from both filter connections, so as to expel
air trapped in the pumps. Otherwise the air may remain trapped,
preventing the pumps from circulating the water.
After filling, make sure both filters are installed properly before
applying power to the spa. (refer to sec. "Cleaning The Filters").
I
Checks
Open the cabinet access panel and check all pump fittings to
make sure they are tight. Loosening can occur during shipping
and handling.
I
Turn on Power
Turn on power to spa from the main switch (refer to the chap-
ter "Electrical safety". The heater and circulation pump will auto-
matically activate.
If the control panel LCD flashes water temperature and "COOL"
or "ICE", refer to "Troubleshooting-Display messages".
I
Startup
Press once on the keys JETS 1 and 2 on the control panel.
I
Addition of chemcial additives at first start-up
Add the spa water chemicals as recommended by your dealer (refer
to the chapter "Water Quality Maintenance" for general guidance).
33
. In particular, an equipotential