Jacuzzi J-460 Manual De Instalación página 46

I
Press DISPLAY sensor once to save changes and return to
the standard water temperature display.
N.B.: If no sensor is pressed within 30 seconds, the screen will
automatically return to the normal water temperature display.
Programming circulation pump run time
The control system allows you to easily adjust two separate
aspects of circulation pump operation:
- the time of day the circulation pump begins operating.
- the length of time the circulation pump operates.
The factory-set start time is 12:00AM (Midnight). The duration
is 24 hours.
I
To make adjustments, press the CYCLE key to enter the cir-
culation pump programming mode: the display shows the mes-
sage "Circ. " .
I
Press the SELECT sensor once: The previously programmed
start time appears on the display.
I
Press ( + ) or ( - ) to adjust the start time in increments of 30
minutes.
I
Press the SELECT sensor to program duration.
I
Press ( + ) or ( - ) to adjust the start time in increments of 1 hour.
I
Press "DISPLAY" to memorize the adjustments you have made:
the main display return to showing the water temperature.
Note: if no keys are pressed within 30 seconds, all of the
changes made are saved and the screen automatically returns
to the standard temperature display.
Note: the circulation pump is activated automatically in stan-
dard mode (if needed) regardless of the programmed start
time and duration.
Locking skimming/heating cycles
You may keep the skimming/heating cycle programs from being
inadvertently altered by electronically locking them.
I
To accomplish this, simply press CYCLE then, within 30 seconds,
press DISPLAY, MODE and ( + ), within five seconds of each other:
a lock symbol will appear on the display. In this state, the status of
the cycle programming may be checked, but may not be altered.
I
To unlock the skimming/heating cycle programming, simply
press DISPLAY, MODE and ( - ) within five seconds each.
Panel Lock
To help prevent unauthorized use of your spa, there is an
exclusive system which deactivates the keys of the panel.
I
To Lock The Panel: Press the DISPLAY, MODE, and ( + ) keys,
in order, within five seconds: A padlock symbol will appear on the
display. With the panel locked, none of the components can be
turned on and the only settings that can be adjusted are the stan-
dard/economy operating mode and changing the time of day.
All automatic spa functions will operate normally.
I
To Unlock The Panel: Press DISPLAY, MODE, and ( - ), in
order, within five seconds: The "lock" symbol will disappear. All
keys are now active.
Temperature Setting Lock
I
To electronically lock the temperature setting, first enter the
"temperature setting" mode by pressing ( + ) or ( - ).
I
Then, within five seconds, press the three keys "DISPLAY",
"MODE" and (+): this will prevent the temperature setting from
being changed by unauthorized persons but all other keys will
remain active.
I To unlock the temperature setting
to unlock the panel.
Spa maintenance
I
Cleaning the filters
A programmable "Change Filter" reminder flashes on the con-
trol panel display after a specified number days to remind you
to clean the skimmer filter and to check the polishing bag filter.
This reminder must be reset at each filter cleaning interval.
Your new spa is equipped with an advanced 2-stage filtration sys-
tem. Fine debris is filtered by the circulation pump drawing water
through the skimmer and pleated filter cartridge every 24 hours
(unless programmed otherwise). Large debris are filtered when
either jets pump is running when the spa is in use or during a
programmed filter cycle. These pumps draw water from footwell
suction fitting and through a secondary water polishing bag fil-
ter. The exclusive footwell "sweeper" suction fitting enhances fil-
tration in the footwell area by creating a "swirling" water motion
to maximize particle agitation and pickup.
To ensure optimum performance, the cartridges (A) and (C) must
be cleaned every three months and replaced once a year and the
secondary polishing filter bag (B) should be emptied weekly and
replaced every 3 months.
Note: attempts to wash the part (B) may make it unusable.
ALWAYS TURN POWER TO THE SPA OFF BEFORE
CLEANING THE FILTER CARTRIDGES!
To accomplish this, refer to the following filter cleaning procedure:
1. Remove power to the hot tub before removing the skimmer
(A) or filter bag cover (B).
2. Remove the polishing bag lid (B) by rotating it counterclock-
wise approximately 5 degrees until you feel it unlatch.
46
simply follow the instructions