Deltaco EV-3226 Manual Del Usuario página 8

1. Button: Switches between 6/8/10/13/16A (Press and hold)
Single press to set a delay timer from 30 minutes to 10 hours.
2. Charging current (In "A" = ampere)
3. Charging time
4. Charge effect in kW/h (currently)
5. Indicates it is ready
6. Indicates it is connected to an electrical vehicle
7. Indicates this device is connected to power.
8. Charging status
9. Delayed start timer
Use
The control box must be hanged up to reduce cable strain
on CEE 16A connector. We recommend that you hang up the
control box via the hook.
Connect the power plug to the power outlet, 3 phase contact.
The display and LEDs will turn on.
Press and hold the button to switch current before connecting
to your car. You can switch between 6/8/10/13/16A.
Single press the button to set a delay timer from 30 minutes to
10 hours. The timer is the time before charging starts. Each long
press increases the time with 30 minutes.
To restart the timer from 0 keep pressing until it reaches 0. To
completely reset the timer, please disconnect the cable from
the power supply and reconnect.
Connect the type 2 plug to your electric vehicle.
The charger automatically detects the connection status and
handshaking protocol and starts charging.
Check the display to confirm it is charging.
Use locations
Typical use locations for this product would be sheltered
locations or areas with roofs, such as a garage or a parking lot
with a roof.
Compatibility
Charger EV-3226 is for all electrical vehicles with Type 2 contacts.
Don't use them with other types.
LED status
Status Red (Fault)
Ready (6A) off
Ready (8A) off
Ready (10A) off
Ready (13A) off
Ready (16A) off
Preparing off
Charging off
Charge
complete off
Fault flashing
Set timer: if a timer is being set, one of the LEDs will be flashing.
Reserved: if the device is in reserved mode the LEDs will be
flashing depending on the currently set current. For example,
with 6A the 3rd LED will flash.
Error codes
If the there is an on-going fault currently in the device, the
display will indicate an error code.
Example: If the residual current device (RCD) has activated it will
show: "01" where "01" is the error code.
Display code: 01. Red LED flashes 1 time. Indicates: current leak-
age, residual current device(RCD) has activated. Solution: Power
the device off and check the electric car and charger.
Display code: 02. Red LED flashes 2 times. Indicates: overcurrent
protection activated. Solution: Power the device off and check
the electric car.
Display code: 03. Red LED flashes 3 times. Indicates: Earth fault
protection activated. Solution: Power the device off and check
the distribution grid.
Display code: 04. Red LED flashes 4 times. Indicates: overvolt-
age/undervoltage protection activated. Solution: Power the
device off and check the distribution grid.
Display code: 05. Red LED flashes 5 times. Indicates: Welding
fault protection activated. Solution: Please contact our support.
Display code: 06. Red LED flashes 6 times. Indicates: communi-
cation error (between control box and car. Solution: Check if the
connectors are tight. Try reconnecting the cables.
Electrical protections
7
Green (1) Green (2) Green (3)
off off on
off on off
on off off
off on on
on on off
flashing flashing flashing
pulsing pulsing pulsing
on on on
off off off
This product has built-in electrical protections. Please see error
codes for trouble shooting.
Self-test
When this product starts up, it runs a self-test to ensure safety.
It checks electrical protections.
The display will turn on. If the self-test is ok, the display stays on,
indicating it is ready.
This is done automatically, and no user action is needed. This
information is provided for troubleshooting purposes.
Cleaning
Disconnect from power and use a dry cloth for cleaning this
device. For difficult stains use a mild detergent and moist cloth
and wipe off with a dry cloth.
Storage
Disconnect the cable from power. We recommend cleaning the
product in case it has any stains before storage.
Support
More product information can be found at
www.deltaco.eu.
Contact us by e-mail: help@deltaco.eu.