Publicidad
Idiomas disponibles
Idiomas disponibles
Section
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1. Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
2. Electrical Requirements
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3. Ceiling Fan Assembly
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
4. Switch Cover Assembly Only . . . . . . . . . . . . . . . . . . . . . .10-14
5. Light Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
6. How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . .16-17
7. How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . .18-22
8. Ceiling Cover Installation . . . . . . . . . . . . . . . . . . . . . . . . .23-24
9. Glass Shade Installation . . . . . . . . . . . . . . . . . . . . . . . . . .24-26
READ AND SAVE THESE INSTRUCTIONS
WARNING
!
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at
service
panel
and
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
1. Read your owner's manual carefully and keep it for future
reference.
2. Be careful of the fan and blades when cleaning, painting,
or working near the fan. Always turn off the power to the
ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off
at the fuse box before wiring, and do not operate fan
without blades.
2. All wiring must be in accordance with the National
Electrical Code "ANSI/NFPA 70-2014" and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and
capable of reliably supporting at least 50 pounds. Use
only U.L. outlet boxes listed as "Acceptable for Fan
Support of 22.7kg. (50 lbs.) or less", and use the mounting
screws provided with the outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
All manuals and user guides at all-guides.com
Table of Contents
Page
Safety Instructions
lock
service
panel
2
Section
10. Transmitter Battery Installation
and Code Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27
11. Receiver Code Learning . . . . . . . . . . . . . . . . . . . . . . . . .28-29
12. Using Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
13. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
14. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
15. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Ceiling Fan Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . .33
16. Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34-35
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance for
an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed by
a licensed electrician.
NOTE: Suitable for use in wet locations when installed in a
GFCI protected branch circuit.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
NOTE: If replacing the original supplied light kit, use
only light kits marked "Suitable for use in wet locations".
C A U T I O N : To reduce the risk of electric shock,
disconnect the electrical supply circuit to the fan before
installing light kit.
WARNING
!
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
A standard wall switch meets this requirement.
To reduce the risk of fire or electric shock, do not use
this fan with any solid-state speed control device.
Solid-state speed controls cannot meet the requirements
of wet location usage, consult Emerson customer
service, 1-800-654-3545 for further assistance.
To avoid fire or electric shock, this fan should only be
used with fan speed control Model No. UC7067RYA,
manufactured by Rhine Electric Co., Ltd.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co.
Substitution of parts or
accessories not designated for use with this product by
Emerson Electric Co. could result in personal injury
or property damage.
To reduce the risk of personal injury, do not bend the
blade holders when installing the blade holder
assemblies, balancing the blades or cleaning the fan. Do
not insert foreign objects in between rotating fan blades.
Page
U.L. Model No.: CF135
Publicidad
