Publicidad
Idiomas disponibles
Idiomas disponibles
Mowing programs – "MODE" button (52)
Use the navigation buttons (55) to go to the
mowing program that you want to start. You can
always choose between "Main area" and "Se-
condary area". More details of the two areas can
be found in the section "Before using for the fi rst
time" under "Perimeter wire".
•
Mowing
When you start the robot lawn mower to mow
the lawn, the mower will switch to normal ope-
rating mode with the set time schedule.
•
Boundary cut
Place the robot lawn mower close to the peri-
meter wire (18) or start the mower while it is in
the charging station (19). With its mower unit
activated, the robot lawn mower will follow
the perimeter wire (18) in counter-clockwise
direction until it reaches the rear of the char-
ging station (19). Provided no work window is
active, the robot lawn mower will then return
to the charging station (19).
•
Spot mowing
It may happen that your robot lawn mower
fails to mow some spots sufficiently. Place the
robot lawn mower at the spot in question and
start the mower. The robot lawn mower will
begin to mow the lawn in a spiral pattern until
it collides with an obstacle or the perimeter
wire (18). Provided no work window is active,
the robot lawn mower will then return to the
charging station (19).
•
Back to station
Send your robot lawn mower back to the
charging station (19). The robot lawn mower
will look for the perimeter wire (18) and follow
it counter-clockwise to the charging station
(19). The secondary area option does not
exist in this case.
6.6 Controlling the robot lawn mower
Starting procedure
1. Press the "STOP" button (3) and open the
display cover (23) fully.
2. Unlock the control panel (2).
3. Use the"MODE" button (52) to select the mo-
wing program and the respective work area
you want.
4. Press the "START" button (53).
5. Close the display cover (23).
The robot lawn mower will now operate in ac-
cordance with the mowing time setting. During
work time the battery charge level will appear on
the LCD (50). Whenever the battery charge level
drops to 30%, the robot lawn mower will return
Anl_ST_400_SPK7.indb 43
Anl_ST_400_SPK7.indb 43
GB
automatically to the charging station (19).
Canceling the mowing operation
1. To bring the robot lawn mower to an immedia-
te stop, press the STOP button (3).
2. Open the display cover (23) fully.
3. Unlock the control panel (2).
4. Press the "MODE" button (52) and select
"Back to station" in order to send the robot
lawn mower along the perimeter wire (18) and
back to the charging station (19).
5. Press the "START" button (53).
6. Close the display cover (23).
STOP status:
When you press the STOP button (3), the robot
lawn mower will adopt a STOP status. This will be
indicated in the LCD (50). The robot lawn mower
will interrupt its mowing until this STOP status is
canceled.
When the control panel (2) is unlocked, a window
will appear and ask if you want to cancel the
STOP status. If you confi rm, the status will be
canceled. If you don't confi rm, the robot lawn mo-
wer will remain stopped. If the robot lawn mower
is started or returned to the charging station (19),
the STOP status will be canceled likewise. Close
the display cover (23).
7. Cleaning, maintenance and
ordering spare parts
Hazard!
The equipment must be disconnected from the
power supply (pull out the power plug and switch
off the equipment by the main switch (7) (OFF)
(Fig. 8) prior to performing any cleaning and
maintenance work. Also take the battery out of
the robot lawn mower.
Caution! Wear work gloves!
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
Do not clean the robot lawn mower with run-
ning water, particularly with high-pressure
water.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
- 43 -
16.11.2023 11:32:29
16.11.2023 11:32:29
Publicidad
