Publicidad
Idiomas disponibles
Idiomas disponibles
In extreme conditions liquid may leak out of the battery. The liquid
coming out of the battery may cause irritations or burns. When a
leak is found, follow the below procedure:
Carefully wipe the liquid with a cloth. Avoid contact of the liquid with
skin and eyes.
In case the liquid gets onto skin, immediately wash the spot
abundantly with clean water, you can also neutralize the liquid with a
mild acid, e.g. lemon juice or vinegar.
When the liquid gets into eyes, wash it immediately with a lot of clean
water for at least 10 minutes. Seek medical advice.
Do not use damaged or modified battery. Damaged or modified
batteries may behave unpredictably, causing fire, explosion or risk of
injuries.
Do not expose the battery to humidity or water.
Always keep the battery away from sources of heat. Do not leave the
battery for a long time in high temperature (in direct sunlight, in proximity
of heaters and wherever the temperature exceeds 50°C).
Do not expose the battery to fire or excessive temperature.
Exposure to fire or temperature above 130°C may cause explosion.
CAUTION! Temperature of 130°C can be also defined as 265°F.
Observe all charging instructions. Do not charge the battery in
temperature outside of range defined in the rating data table from
the instruction manual. Incorrect charging or charging in temperature
outside of defined range may damage the battery and increase the risk of
fire.
BATTERY REPAIRS
Do not repair damaged batteries. Battery can be repaired only by the
manufacturer or in an authorised workshop.
When disposing of the worn out battery, take it to a service point
where you can utilize such dangerous wastes.
SAFETY REGULATIONS FOR THE CHARGER
Do not expose the charger to humidity or water. Ingress of water
into the charger increases risk of electric shock. Use the charger only in
dry rooms.
Disconnect the charger from power supply before starting any
maintenance or cleaning.
Do not use the charger when placed on flammable surface (e.g.
paper, textiles) or in proximity of flammable substance. Greater
charger temperature when charging increases risk of fire.
Check condition of the charger, cable and plug before each use.
Do not use the charger if any damage is found. Do not try to
disassemble the charger. All repairs should be made at an authorized
service workshop. Improper charger assembly may cause electric shock
or fire.
Children or persons who are physically, emotionally or mentally
disabled and other persons, whose experience or knowledge is
insufficient to use the charger while following all safety rules should not
use the charger without supervision of person responsible for their safety.
Otherwise there is a risk of improper use and injuries in consequence.
When the charger is not in use, it should be disconnected from
the mains network.
Observe all charging instructions. Do not charge the battery in
temperature outside of range defined in the rating data table from
the instruction manual. Incorrect charging or charging in temperature
outside of defined range may damage the battery and increase the risk of
fire.
CHARGER REPAIRS
Do not repair damaged charger. The charger can be repaired only by
the manufacturer or in an authorised workshop.
When disposing of the worn out charger, take it to a service point
where you can utilize such wastes.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of injuries at work.
Li-Ion batteries may leak, set on fire or explode when heated to high
temperature or short-circuited. Do not store the batteries in a car in
hot and sunny days. Do not open the battery. Li-Ion batteries contain
electronic protection devices that, if damaged, may cause fire or
explosion of the battery.
Explanation of used symbols
1. Read instruction manual, observe warnings and safety conditions
therein.
2. Use protective goggles and hearing protectors.
3. Keep the tool away from children.
4. Protect against rain.
5. Use indoors, protect from water and moisture.
6. Recycling.
7. Protection class 2.
8. Segregated waste collection.
9. Do not throw cells into fire.
10. Hazardous to water environment.
11. Do not allow to heat above 50°C.
CONSTRUCTION AND USE
The impact driver is a battery-powered tool. The drive consists of DC
commutator motor with permanent magnets. The impact driver is used for
tightening and undoing screws and bolts in wood, metal or plastics. High
speed allows to use the device widely for self drilling screws, and high
torque allows to use the device for long screws in wood. The device can
be well used at heights and in hard to reach areas. High torque mechanism
creates the torque as short, high peaks of circumferential impact, and tool
reactions towards the operator's hands during tightening is low.
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the drawing
pages of this manual.
1. Tool chuck
2. Fixing sleeve of the tool chuck
3. Casing
4. Direction selector switch
5. Holder
6. Battery
7. Battery lock button
8. Switch
9. Lighting
10. Charger
11. Battery level indicator (LED)
* Differences may appear between the product and drawing.
EQUIPMENT AND ACCESSORIES
1. Battery
2. Charger
3. Screwdriver bit
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
Set the direction selector switch (4) in middle position.
Push the battery lock button (7) and slide out the battery (6) (fig. A).
Insert charged battery (6) into the handle holder, you should hear when
the battery lock button (7) snaps.
BATTERY CHARGING
The device is supplied with partially charged battery. The battery should
be charged in ambient temperature between 4°C and 40°C. In the event
of a longer storage of the battery, it is recommended to check the state of
its charge and possibly recharge it every few months.
Remove the battery (6) from the device (fig. A).
Connect the charger to mains socket (230 V AC).
Slide the battery (6) into the charger (10) (fig. B). Ensure the battery is
properly fitted (pushed to the end).
After connecting the charger to the mains, the LED (11) on the charger
(10) lights up green. The LED lighting system is described below.
• Green light of the diode - indicates voltage connection.
6
- 1 pc
- 1 pc
- 1 pc.
Publicidad
