Publicidad
Idiomas disponibles
Idiomas disponibles
TO LEVEL
MOWER
HOUSING
Adjust
the mower while
tractor
is parked
on level ground
or driveway.
Make sure
tires are properly
inflated
(See "PROD-
UCT SPECIFICATIONS"
section
of this
manual).
If tires are over or underinflated,
you will not properly
adjust your mower.
SIDE-TO-SIDE
ADJUSTMENT
• Raise mower
to its highest
position.
• At the midpoint
of both sides of mower,
measure
height from bottom
edge of
mower
to ground.
Distance
"A" on both
sides of mower should
be the same or
within
1/4" of each other.
• If adjustment
is necessary,
make adjust-
ment on one side of mower only.
• To raise one side of mower,
tighten
lift
link adjustment
nut on that side.
• To lower one side of mower,
loosen
lift
link adjustment
nut on that side.
NOTE:
Each full turn of adjustment
nut
will change
mower
height about
1/8".
• Recheck
measurements
after adjusting.
Bottom edge of
Bottom edge
_
mower to ground
of mower to f--_, _
!_,--_ /
ground-,__`
___!_-:t_
A I 1:1 °== _ Grouund Line ÷_"=°i) _ I A
Arm
Lift Link
Adjustment Nut
FRONT-TO-BACK
ADJUSTMENT
IMPORTANT:
Deck must be level side-to
side. If the following front-to-back
adjust-
ment is necessary, be sure to adjust both
front links equally so mower will stay level
side-to-side.
To obtain the best cutting results, the
mower housing should be adjusted so
that the front is approximately
1/8" to 1/2"
lower than the rear when the mower is in
its highest position.
Check adjustment on right side of trac-
tor. Measure distance "D" directly in front
and behind the mandrel at bottom edge of
mower housing as shown.
• Before making any necessary adjust-
ments, check that both front links are
equal in length.
• If links are not equal in length, adjust
one link to same length as other link.
• To lower front of mower loosen nut "E"
on both front links an equal number of
turns.
• When
distance
"D" is 1/8" to 1/2"
lower at front than rear, tighten
nuts "F"
against
trunnion
on both front links.
• To raise front of mower,
loosen
nut "F"
from trunnion
on both front links. Tighten
nut "E" on both front links an equal
number
of turns.The
two front links must
remain
equal in length.
• When
distance
"D" is 1/8" to 1/2" lower
at front than rear, tighten
nut "F" against
trunnion
on both front links.
• Recheck
side-to-side
adjustment.
Both Front Links Should be Equal in Length
Nut
,_E
_
Trunnion
Front Links
TO REPLACE
MOWER
BLADE
DRIVE
BELT
The mower
blade drive belt may be re-
placed
without
tools.
Park the tractor
on
level surface.
Engage
parking
brake.
BELT REMOVAL
-
1. Remove
mower
from tractor
(See "TO
REMOVE
MOWER"
in this section
of
manual).
2.
Work belt off both mandrel
pulleys
and
idler pulleys.
3.
Pull belt away from mower.
BELT INSTALLATION
-
1. Work belt around
both mandrel
pulleys
and idler pulleys
2.
Make sure belt is in all pulley grooves
and inside
all belt guides.
3.
Install mower
(See "To Install
Mower"
in this section
of this manual).
23
Publicidad
