Descargar Imprimir esta página

gomag GO-HHS410 Traduccion Del Manual De Instrucciones Originale página 42

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

13 Maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the
battery removed. There is a danger of inju-
ry! Let the Product cool down before all
maintenance and cleaning tasks. Elements
of the engine are hot. There is a danger of
injury and burning!
The product can start unexpectedly and cause inju-
ries.
Remove the battery.
Allow the product to cool down.
Remove the tool attachment.
• Check the product for obvious defects such as
loose, worn or damaged parts before each use.
• Check the covers and protective devices for dam-
age and correct seating. Replace them if necessary.
• Regular, careful servicing is required to guarantee
the safety level and performance of the product.
• Position the Product on a straight, level surface.
• Do not splash the product with water.
• For safety reasons, replace worn or damaged parts.
• Any work not described in this operating manual
must be performed by an authorised specialist
workshop only.
Notes:
Maintain the product carefully. Check for misalignment
or binding of moving parts, breakage of parts and any
other condition that may affect the product's operation.
Have damaged parts repaired before using the product.
13.1
Hedge trimmer
1. Check that the screws in the cutter bar are tight.
2. You can smooth out slight nicks on the cutting teeth
yourself. To do this, draw an oil stone along the cut-
ting edges. Only sharp cutting teeth provide a good
cutting performance.
3. Blunt, bent or damaged cutter bars must be re-
placed.
42 | GB
13.2
Pole-mounted pruner
WARNING
Danger of injury when handling the saw
chain or the blade!
Wear cut-resistant gloves.
13.2.1
1. Turn the screw (18) for the chain tensioning system
anti-clockwise to slacken the chain tension and re-
move the chain cover (21).
2. Remove the guide bar (16) and the saw chain (17).
3. Measure the groove depth of the chainsaw guide
bar (16) with the scale on a file gauge (not included
in scope of delivery).
4. The chainsaw guide bar (16) must be replaced if
any of the following apply:
– The chainsaw guide bar is damaged.
– The measured groove depth is smaller than the
minimum groove depth of the chainsaw guide
bar (4 mm).
– The groove of the chainsaw guide bar has nar-
rowed or spread.
5. Fit the chainsaw guide bar (16) and saw chain (17)
as described under 8.1.
13.2.2
1. Turn the screw (18) for the chain tensioning system
anti-clockwise to slacken the chain tension and re-
move the chain cover (21).
2. Remove the guide bar (16) and the saw chain (17).
3. Check the grooving on the chain wheel (22) with a
test gauge (not included in the scope of delivery).
4. If the grooves are deeper than 0.5 mm, do not use
the product and consult a specialist dealer. The
chain wheel (22) must be replaced.
5. Fit the chainsaw guide bar (16) and saw chain (17)
again as described under 8.1.
13.2.3
1. Turn the screw (18) for the chain tensioning system
and the chain cover (21) anti-clockwise to slacken
the chain tension and remove the chain cover (21).
2. Remove the guide bar (16) and the saw chain (17).
3. For dismantling, hold the guide bar (16) swivelled
upwards at an angle of approx. 45 degrees to make
it easier to remove the saw chain (17) from the
groove of the chainsaw guide bar (16).
4. Replace the chainsaw guide bar (16) and fit the
chainsaw guide bar (16) and saw chain (17) as de-
scribed under 8.1.
www.scheppach.com
Checking the chainsaw guide bar
(16) (Fig. 2, 3)
Checking the sprocket (22) (Fig.
2-4)
Replacing the chainsaw guide bar
(16) (Fig. 2, 3)

Publicidad

loading

Productos relacionados para gomag GO-HHS410

Este manual también es adecuado para:

39124039982