Ventilation System; Channeling System; Stoves Mod. Abril-Ex And Models With Optional Channeling Kit; 8.2 How To Install The Optional Channeling Kit - Bio Bronpi Aire Serie Instrucciones De Instalación, Uso Y Mantenimiento

7

VENTILATION SYSTEM

All models of stoves incorporate a convection turbine as standard for the heating of the environment, the operation of this turbine is in line with
the working power of the stove, so that with the stove on, the turbine will always remain working.
On the other hand, the model Abril has the possibility to activate or deactivate the operation of the main convection turbine of the stove. From
the display you can deactivate the turbine operation. This way, the stove will perform the heating of the environment through the radiation of
the stove itself and by natural convection.
If it is chosen to activate the operation of the turbine, the heating of the environment is also produced by the radiation of the stove and, in this
case, by forced convection.
To activate or deactivate turbine operation, refer to the section of this manual 10.4.10 Menu 9: "Fan mode".
8

CHANNELING SYSTEM

Below is detailed the operation of the air distribution system to other adjacent or upper rooms of the stoves including this system.
8.1

STOVES MOD. ABRIL-EX AND MODELS WITH OPTIONAL CHANNELING KIT

Whether the duct fan is included as standard in the oven or one or two optional channeling kits (depending
on the model) are purchased, the channeling diameter must be 80 mm, and both the number of channeling
and the maximum channeling distances must be respected according to the model specifications. The
greater the distance and/or the greater the number of pipes, the smaller the flow rate will be.
The regulation of the channelling system is made by the electronic system of the stove, therefore you can
choose the operation of each one of the pipes and the power level desired to each fan independently. To
do this you have to gain access to menu 1 and choose the fan activation and the working power (see
drawing D12).
Menú 01
VENT-2 1
D13
- First, you have to remove the side chambers of the stove to access the inside of it.
- Then place the connector and the turbine in the right position and fix it by positioning and tightening the screws supplied.
- Finally, connect the existing cable in the turbine, with the electronic plate of the stove, to the connector CN6 "V2 / PO". Do not forget to
cut off the electrical power of the stove, before making this connection.
On the other hand, the Eva and Coral models allow the connection of two channeling kits; in order to install them, follow the previous steps,
but when connecting to the electronic board, to control the fan 2 on the display, the fan 2 must be connected to the CN6 connector "V2/PO"
and to control the fan 3 on the "AUX-1" connector. You can select the outlet of the channeling through the back or side of the stove, for this
you must remove the existing pre-cut. Do not forget to turn off the power before making this connection.
9

SERVICING AND CARE

The maintenance operations guarantee a proper working of the product over its lifetime. Not making these maintenance operations will affect
the security of the product.
9.1

BURNER CLEANING

The burner cleaning must be made daily (see drawing D15).
• Remove the burner from its place and clean the holes.
• Use a vacuum to get rid of the ashes in the burner. You can buy
a Bronpi vacuum-cleaner in the same Bronpi distributor where you
bought your stove.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS
NOTE: Please note that if you've purchased a Tina model or you have
not purchased an optional channeling kit, this menu is visible but is not
operational. In the models Rita, Zoe, Nina, Kira, Alba, Noa, Noa Vision, Leticia, Princesa and Abril-Ex, it is
only possible to modify the speed of the fan number 2 because they only have one channeling fan (see
drawing D13).

8.2 HOW TO INSTALL THE OPTIONAL CHANNELING KIT

If you have purchased an optional channeling for models that only allow one channeling, the kit consists of
a fan with the connector and the interconnection cable with the electrical board, you should consider the
following steps for a correct installation. (see drawing D14)
29
D12
Menu 01
FAN-2 1
FAN-3 A
D14
D15
AIR SERIES