Parts List - Multiplex Alpina-4001Elektro Instrucciones De Montaje

will be hinged permanently and invisibly to the wing, and
will move freely up and down.
Applying the decals
Cut out the decals and apply them to the model.
There are two convenient methods of applying the individual
decals included in the decor set, both of which enable you
to position the decal accurately: the strip method and the
water method.
For smaller items we recommend the strip method: using
sharp scissors cut out the decal, leaving an even excess
about 1 - 2 mm wide all round. Release the backing paper
on one edge and cut a strip about 5 mm wide from it. Place
the decal on the model and position it carefully, holding the
exposed strip away from the surface. When you are happy,
press the exposed strip down. Fold the decal back on itself
so that you can peel off the remaining backing paper

Parts list

Alpina 4001 ELEKTRO
Part No. Description
No. off
1 1 Building instructions
2 1 Decal set (name placard)
3 1 Epoxy fuselage
4 1 Canopy
5 1 Pair of wing panels
6 1 Pair of tailplane panels
7 1 Rudder
Wooden parts
10 1 Motor bulkhead
11 1 Servo plate
12 1 Former
13 1 Battery tray, bottom
14 2 Battery tray, side reinforcement
15 1 Channeled strip, canopy
16 1 Compression strut, front / rear
17 4 Airbrake support strip
18 4 Airbrake surround strip
19 2 Airbrake capstrip
Hardware items
40 12 Metal clevis
41 2 Threaded coupler
42 2 Threaded rod
43 2 Threaded rod
44 5 Ring-screw (horn)
45 6 Hexagon nut
46 2 MULTIlock plug
47 2 MULTIlock socket (in fuselage)
48 1 Wing joiner rod
49 4 Steel rod
50 12 Plastic film hinge (2 x 6 off)
51 3 Snap-fit hinge lug
52 2 Self-tapping screw
53 2 Rubber grommet
54 1 All-moving tailplane crank
55 1 Brass tube
56 2 Bearing nut
57 1 Threaded bush
26
starting from the stuck edge. At the same time rub the decal
down onto the model with your other hand, starting from
the edge already in place. For larger decals the strip
method can only be recommended to the highly skilled
modeller; generally speaking the water method is safer.
The surface to be decorated must be waterproof. Mix a
squirt of household liquid detergent into a bowl of water,
and dampen the surface of the model with the solution. Cut
out the decal as before, leaving an even excess about 1 -
2 mm wide all round, and remove about one third of the
backing paper. Position the decal carefully, then peel away
the remaining backing paper. Lay the decal down on the
model. You will find that the water prevents the adhesive
sticking, and the decal can be moved around to position
it accurately. Wipe out any air bubbles and excess water,
working from the centre of the decal outwards. The residual
moisture will diffuse away in a day or two, after which the
decal will adhere in the usual way. In the meantime it is
best not to touch the decal.
Purpose Material
Paper
Printed film
White GRP
Carbon fibre
Foam / obechi
Foam / obechi / balsa
Foam / obechi
Fuselage Birch ply
Fuselage Plywood
Fuselage Obechi
Fuselage Plywood
Fuselage Obechi
Fuselage Obechi
Fuselage Obechi
Wings Balsa
Wings Lime
Wings Obechi
Control linkages Steel
Control linkages Brass
Control linkages Steel
Control linkages Steel
Control surfaces Aluminium
Clevis locknut Brass
Wing retainer Plastic
Wing retainer Plastic
Wings Spring steel
Wing locating pin Spring steel
Aileron / flap Plastic
Rudder Plastic
Battery tray Steel
Battery tray Rubber
Fuselage Plastic
Tailplane bearing Brass
Tailplane bearing Aluminium
Tailplane bearing Brass tube
Dimensions
A4
Ready made
Ready made
Ready made
Ready made
Ready made
Ready made
Machined
Machined
Machined, 14 thick
Pre-sawn, 3 mm
10 x 5 x 410 mm
Pre-sawn
10 x 10 x 85 mm
5 x 20 x 370 mm
1.8 x 4 x 380 mm
1.8 x 12 x 380 mm
M2.5
M2.5
M2.5 x 40 mm
M2.5 x 65 mm
M4
M2.5
Inj. moulded
Inj. moulded
12 Ø x 330 mm
3 Ø x 60 mm
Ready made
Inj. moulded
2.2 Ø x 13 mm
Ready made
Inj. moulded
6 Ø x 0.45 x 5 mm
Ready made
3 Ø x M5 x 17 mm